manualshive.com logo in svg

Cisco 901, Command Reference Manual

The Cisco 901 Installation Manual is a comprehensive guide for setting up and configuring your Cisco 901 product. This manual is available for free download from our website, ensuring a hassle-free experience. Get your hands on the detailed manual for the Cisco 901 at manualshive.com.

Share
Download
background image

1-13

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1      CLI Command Reference

  asr901-multicast source

asr901-multicast source

To send the multicast packets to the CPU enabling it to transmit register packets to Rendezvous Point 
(RP), use the 

asr901-multicast source

 command on the interface configuration mode. Use the 

no

 form 

of the command to disable transmission of multicast packets. 

asr901-multicast source

no asr901-multicast source

Syntax Description

This command has no arguments or keywords.

Command Default

This command is enabled by default.

Command Modes 

Interface configuration (config-if)#

Command History

Usage Guidelines

This command should be enabled on the SVI interface that is connected to the traffic source. After the 
configuration, normal Protocol Independent Multicast sparse mode (PIM-SM) register process begins. 

Examples

This example shows how to enable multicast on a Cisco ASR 901 series router:

Router# 

configure terminal

Router(config)# 

interface

 

type number

Router(config-if)# 

asr901-multicast source

Release

Modification

15.4(1)S

This command was introduced on the Cisco ASR 901 Series Aggregation 
Services Routers.

Summary of Contents for 901



























































































































































































































Reviews:

No comments

Related manuals for 901

Cabletron Systems Netlink FRX4000 Installation And Setup Manual preview
Netlink FRX4000
Brand: Cabletron Systems Pages: 8
Cabletron Systems 9C300-1 Upgrade Instructions preview
9C300-1
Brand: Cabletron Systems Pages: 4
Cabletron Systems MMAC-Plus 9F106-02 Reference Manual preview
MMAC-Plus 9F106-02
Brand: Cabletron Systems Pages: 7
Idis DR-4100P Series Installation Manual preview
DR-4100P Series
Brand: Idis Pages: 30
Clavister NetWall W20A Getting Started Manual preview
NetWall W20A
Brand: Clavister Pages: 89
EVOC 6336-STG-YX Manual preview
6336-STG-YX
Brand: EVOC Pages: 57
Thecus N12000 series User Manual preview
N12000 series
Brand: Thecus Pages: 120
PairGain T1L2PY0AA Manual preview
T1L2PY0AA
Brand: PairGain Pages: 80
Microtek MiniLink Operation Manual preview
MiniLink
Brand: Microtek Pages: 25
Pullnet AGENT-2 S41D Line User Manual preview
AGENT-2 S41D Line
Brand: Pullnet Pages: 89
ActiveEye K9504L-W Operation Manual preview
K9504L-W
Brand: ActiveEye Pages: 35
Tripp Lite N201-014-BL Specification Sheet preview
N201-014-BL
Brand: Tripp Lite Pages: 3
Garderos R-3700 Series Operating Manual preview
R-3700 Series
Brand: Garderos Pages: 21
TRENDnet TDM-C400 User Manual preview
TDM-C400
Brand: TRENDnet Pages: 205
Devolo dLAN 200 AVsmart+ Technical Data preview
dLAN 200 AVsmart+
Brand: Devolo Pages: 2
Comnet CNGE28FX4TX24MS2 Installation And Operation Manual preview
CNGE28FX4TX24MS2
Brand: Comnet Pages: 154
TP-Link Archer AX10000 Quick Installation Manual preview
Archer AX10000
Brand: TP-Link Pages: 2
Netstor NA762TB3 User Manual preview
NA762TB3
Brand: Netstor Pages: 17

Brands by name

Popular brands

Load more brands