Cisco 901 Command Reference Manual Download Page 208 | Manualshive

Page: 208 / 218

background image

1-194

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1 CLI Command Reference

speed

Speed and Duplex Combinations

Table 1-14

describes the interface behavior for various combinations of the

duplex

and

speed

command

settings. The specified

duplex

command configured with the specified

speed

command produces the

resulting system action.

If you decide to configure the interface speed and duplex commands manually, and enter a value (for
example, speed 10 or speed 100 ), ensure that you configure the connecting interface speed command to
a matching speed.

You cannot set the duplex mode to

half

when the port speed is set at 1000 and similarly, you cannot set

the port speed to

1000

when the mode is set to half duplex.

Caution

Changing the interface speed and duplex mode might shut down and reenable the interface during the
reconfiguration.

Examples

The following example specifies advertisement of 10 Mbps operation only, and either full-duplex or
half-duplex capability during autonegotiation:

Router#

configure terminal

Router(config)#

interface gigabitethernet 0/1

Router(config-if)#

speed 10

Router(config-if)#

duplex full

With this configuration, the interface advertises the following capabilities during autonegotiation:

•

10 Mbps and half duplex

•

10 Mbps and full duplex

Related Commands

Table 1-14

Relationship Between duplex and speed Commands

duplex Command

speed Command

Resulting System Action

duplex half

speed 10

Forces 10-Mbps and half-duplex operation, and
disables autonegotiation on the interface.

duplex full

speed 10

Forces 10-Mbps and full-duplex operation, and
disables autonegotiation on the interface.

duplex half

speed 100

Forces 100-Mbps and half-duplex operation, and
disables autonegotiation on the interface.

duplex full

speed 100

Forces 100-Mbps and full-duplex operation, and
disables autonegotiation on the interface.

duplex full

speed 1000

Forces 1000-Mbps and full-duplex operation,
and disables autonegotiation on the interface
(Gigabit Ethernet only).

Command

Description

duplex

Configures the duplex operation on an interface.

interface gigabitethernet

Selects a particular Gigabit Ethernet interface for configuration.

«
...
206
207
208
209
210
...
»

Summary of Contents for 901



























































































































































































































Reviews:

No comments

Related manuals for 901

Brand: 3Com Pages: 20

Brand: i-MO Pages: 58

Brand: REXROTH Pages: 68

Sure Cross DX70

Brand: Banner Pages: 35

Brand: XMOS Pages: 6

Brand: VCS Pages: 118

Brand: Idis Pages: 22

Brand: Nexxt Pages: 2

Brand: LevelOne Pages: 4

Xtreme Networked Boat

Brand: Broadband Products Pages: 16

7798 I/SITE LAN

Brand: CSI Pages: 56

Brand: Geneko Pages: 8

VDA-NVR2108W4KS2

Brand: Dahua Technology Pages: 363

Brand: Orcomm Pages: 10

Brand: TP-Link Pages: 32

Brand: Westermo Pages: 18

Brand: Cisco Pages: 160

Brand: Edimax Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands