manualshive.com logo in svg

Cisco 901, Command Reference Manual

The Cisco 901 Installation Manual is a comprehensive guide for setting up and configuring your Cisco 901 product. This manual is available for free download from our website, ensuring a hassle-free experience. Get your hands on the detailed manual for the Cisco 901 at manualshive.com.

Share
Download
background image

1-105

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1      CLI Command Reference

  pseudowire-class

pseudowire-class

To specify the name of a Layer 2 pseudowire-class and enter

 

pseudowire-class configuration mode, use 

the 

pseudowire-class

 command in global configuration mode. To remove a pseudowire class 

configuration, use the 

no

 form of this command.

pseudowire-class 

pw-class-name

no pseudowire-class 

pw-class-name

Syntax Description

Defaults

No pseudowire-class is defined. 

Command Modes

Global configuration 

Command History

Usage Guidelines

The 

pseudowire-class

 command configures a pseudowire-class template that consists of configuration 

settings used by all attachment circuits bound to the class. A pseudowire-class includes the following 
configuration settings: 

•

Data encapsulation type 

•

Control protocol 

•

IP address of the local Layer 2 interface 

•

Type of service (ToS) value in IP headers 

The local interface name for each pseudowire class configured between a pair of PE routers can be the 
same or different.

After entering the 

pseudowire-class

 command, the router switches to pseudowire-class configuration 

mode where PW settings can be configured.

Examples

The following example shows how to enter pseudowire-class configuration mode to configure a PW 
configuration template named “ether-pw”: 

Router# 

config t

Router(config)# 

pseudowire-class mpls

Router(config-pw-class)# 

encapsulation mpls

Router(config-pw-class)# 

exit

Router(config)# 

exit

pw-class-name 

The name of a Layer 2 pseudowire-class.If you want to configure more than 
one pseudowire class, define a class name using the 

pw-class-name 

parameter.

Release

Modification

15.1(2)SNG

Support for this command was introduced on the Cisco ASR 901 router.

Summary of Contents for 901



























































































































































































































Reviews:

No comments

Related manuals for 901

NETGEAR RAXE500 User Manual preview
RAXE500
Brand: NETGEAR Pages: 169
QNAP Turbo NAS TVS-71 Series Hardware User Manual preview
Turbo NAS TVS-71 Series
Brand: QNAP Pages: 51
NETGEAR RBRE960B User Manual preview
RBRE960B
Brand: NETGEAR Pages: 152
Edimax GS-5208PLG V2 Quick Installation Manual preview
GS-5208PLG V2
Brand: Edimax Pages: 15
TRENDnet TEW-823DRU Quick Installation Manual preview
TEW-823DRU
Brand: TRENDnet Pages: 10
Lanner NCA-6520 User Manual preview
NCA-6520
Brand: Lanner Pages: 141
SMC Networks SMCGS10P-Smart Installation Manual preview
SMCGS10P-Smart
Brand: SMC Networks Pages: 68
Axtrinet APG200 User Manual preview
APG200
Brand: Axtrinet Pages: 49
YDI WL2400-ISA Installation & Operation Manual preview
WL2400-ISA
Brand: YDI Pages: 16
BinTec BIANCA/BRICK XS Quick Install Manual preview
BIANCA/BRICK XS
Brand: BinTec Pages: 2
I-Tech NW117HD-8Ke User Manual preview
NW117HD-8Ke
Brand: I-Tech Pages: 6
Paradyne 1754 SHDSL Quick Installation Instructions preview
1754 SHDSL
Brand: Paradyne Pages: 1
Advantage Boost Box Setup Manual preview
Boost Box
Brand: Advantage Pages: 4
D-Link DNS-1560-04 User Manual preview
DNS-1560-04
Brand: D-Link Pages: 95
D-Link DNS-1250-04 User Manual preview
DNS-1250-04
Brand: D-Link Pages: 124
D-Link DNS-1200-5 User Manual preview
DNS-1200-5
Brand: D-Link Pages: 164
D-Link DNS-300 Manual preview
DNS-300
Brand: D-Link Pages: 70
Mitsubishi Electric AT-50A Installation Manual preview
AT-50A
Brand: Mitsubishi Electric Pages: 16

Brands by name

Popular brands

Load more brands