manualshive.com logo in svg

Cisco 901, Command Reference Manual

The Cisco 901 Installation Manual is a comprehensive guide for setting up and configuring your Cisco 901 product. This manual is available for free download from our website, ensuring a hassle-free experience. Get your hands on the detailed manual for the Cisco 901 at manualshive.com.

Share
Download
background image

1-83

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1      CLI Command Reference

  network-clock switch force

network-clock switch force

To forcefully select a synchronization source irrespective of whether the source is available and is within 
the range, use the 

network-clock switch force

 command. Use the 

network-clock clear switch

 

command to remove the forced switch command.

network-clock switch force {interface 

interface_name slot/port

 | external 

slot/card/port

}

Syntax Description

Command Modes

Global configuration.

Command History

Examples

This example forcefully selects the synchronization source:

Router(config)#

network-clock switch force interface GigabitEthernet 0/1 t1

interface_name

Specifies the interface name.

slot/card/port

Specifies the external slot/card/port name.

Release

Modification

15.1(2)SNG

Support for this command was introduced on the Cisco ASR 901 router.

Summary of Contents for 901



























































































































































































































Reviews:

No comments

Related manuals for 901

D-Link DSL-504T Manual preview
DSL-504T
Brand: D-Link Pages: 99
D-Link DI-804V Datasheet preview
DI-804V
Brand: D-Link Pages: 5
D-Link DES-1210-08P Manual preview
DES-1210-08P
Brand: D-Link Pages: 15
D-Link AirPro DWL-6000AP Manual preview
AirPro DWL-6000AP
Brand: D-Link Pages: 65
D-Link DES-7200 User Manual preview
DES-7200
Brand: D-Link Pages: 100
D-Link DES-3226L Manual preview
DES-3226L
Brand: D-Link Pages: 134
D-Link DES-3010F Command Line Interface Manual preview
DES-3010F
Brand: D-Link Pages: 187
D-Link DES-3010F Manual preview
DES-3010F
Brand: D-Link Pages: 225
D-Link DES-1048G Manual preview
DES-1048G
Brand: D-Link Pages: 31
D-Link DES-1050G User Manual preview
DES-1050G
Brand: D-Link Pages: 35
D-Link DES-1016D - Switch Quick Install Manual preview
DES-1016D - Switch
Brand: D-Link Pages: 19
D-Link COVR-2202 User Manual preview
COVR-2202
Brand: D-Link Pages: 107
D-Link AirPlusXtremeG DI-624 Troubleshooting preview
AirPlusXtremeG DI-624
Brand: D-Link Pages: 5
D-Link DGS-1210-28P Getting Started Manual preview
DGS-1210-28P
Brand: D-Link Pages: 48
i-MO 540 Series Product Installation Manual preview
540 Series
Brand: i-MO Pages: 58
Alcatel OmniSwitch 6624 Network Configuration Manual preview
OmniSwitch 6624
Brand: Alcatel Pages: 546
Patton electronics SmartNode 4634 Series Quick Start Manual preview
SmartNode 4634 Series
Brand: Patton electronics Pages: 12
TP-Link TL-WR840N Quick Installation Manual preview
TL-WR840N
Brand: TP-Link Pages: 2

Brands by name

Popular brands

Load more brands