Cisco 901 Command Reference Manual Download Page 105

Page: 105 / 218

1-91

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1 CLI Command Reference

police (percent)

Command Default

All Supported Platforms

The default bc and be values are 4 ms.

Command Modes

Policy-map class configuration (config-pmap-c)

Command History

action

(Optional) Action to take on packets. Specify one of the following keywords:

All Supported Platforms

•

drop

—Drops the packet.

•

set-clp-transmit

—Sets the ATM Cell Loss Priority (CLP) bit from 0

to 1 on the ATM cell and sends the packet with the ATM CLP bit set to 1.

•

set-dscp-transmit

new-dscp

—Sets the IP differentiated services code

point (DSCP) value and sends the packet with the new IP DSCP value
setting.

•

set-frde-transmit

—Sets the Frame Relay discard eligible (DE) bit from

0 to 1 on the Frame Relay frame and sends the packet with the DE bit set
to 1.

•

set-prec-transmit

new-prec

—Sets the IP precedence and sends the

packet with the new IP precedence value setting.

•

transmit

—Sends the packet with no alteration.

•

policed-dscp-transmit

—(Exceed and violate action only). Changes the

DSCP value per the policed DSCP map and sends the packet.

•

set-cos-inner-transmit

value

—Sets the inner class of service field as a

policing action for a bridged frame on the Enhanced FlexWAN module,
and when using bridging features on SPAs.

•

set-cos-transmit

value—Sets the packet cost of service (CoS) value and

sends the packet.

•

set-mpls-exposition-transmit

—Sets the Multiprotocol Label

Switching (MPLS) experimental bits from 0 to 7 and sends the packet
with the new MPLS experimental bit value setting.

•

set-mpls-topmost-transmit

—Sets the MPLS experimental bits on the

topmost label and sends the packet.

Release

Modification

15.1(2)SNG

Support for this command was introduced on the Cisco ASR 901 router.

Summary of Contents for 901



























































































































































































































Search results

Summary of Contents for 901

Reviews:

Related manuals for 901

Brands by name

Popular brands

Cisco 901, Command Reference Manual

Search results

Summary of Contents for 901

Reviews:

Related manuals for 901

Brands by name

Popular brands