manualshive.com logo in svg

Cisco 901, Command Reference Manual

The Cisco 901 Installation Manual is a comprehensive guide for setting up and configuring your Cisco 901 product. This manual is available for free download from our website, ensuring a hassle-free experience. Get your hands on the detailed manual for the Cisco 901 at manualshive.com.

Share
Download
background image

1-65

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1      CLI Command Reference

  mtu

mtu

To adjust the maximum packet size or maximum transmission unit (MTU) size, use the 

mtu

 command 

in interface configuration mode, connect configuration mode, or xconnect subinterface configuration 
mode. To restore the MTU value to its original default value, use the 

no

 form of this command. 

mtu

 

bytes

no mtu

Syntax Description

Command Default

Table 1-3

 lists default MTU values according to media type.

Command Modes

Interface configuration (config-if)
Connect configuration (xconnect-conn-config)
xconnect subinterface configuration (config-if-xconn)

Command History

Usage Guidelines

Each interface has a default maximum packet size or MTU size. This number generally defaults to the 
largest size possible for that interface type. 

Note

The connect configuration mode is used only for Frame Relay Layer 2 interworking.

Changing the MTU Size

Changing the MTU size is not supported on a loopback interface. 

bytes

MTU size, in bytes.

Table 1-3

Default Media MTU Values

Media Type

Default MTU (Bytes)

Ethernet

1500

Serial

1500

Token Ring

4464

ATM

4470

FDDI

4470

HSSI (HSA)

4470

Release

Modification

15.1(2)SNG

Support for this command was introduced on the Cisco ASR 901 router.

Summary of Contents for 901



























































































































































































































Reviews:

No comments

Related manuals for 901

PACOM Professional Series Quick Manual preview
Professional Series
Brand: PACOM Pages: 15
Wave wifi EC Series Quick Start Manual preview
EC Series
Brand: Wave wifi Pages: 2
QNAP QMiroPlus-201W Quick Installation Manual preview
QMiroPlus-201W
Brand: QNAP Pages: 20
Salusfin SF-930EU User'S Installation Manual preview
SF-930EU
Brand: Salusfin Pages: 6
Draytek VigorIPPBX 2820 Series Quick Start Manual preview
VigorIPPBX 2820 Series
Brand: Draytek Pages: 29
Opengear IMG4216-25 Quick Start Manual preview
IMG4216-25
Brand: Opengear Pages: 2
Quectel Wi-Fi-M.2 EVB User Manual preview
Wi-Fi-M.2 EVB
Brand: Quectel Pages: 23
Paradyne Comsphere 3510 User Manual preview
Comsphere 3510
Brand: Paradyne Pages: 85
Garland EdgeLens INT10G8LR56 User Manual preview
EdgeLens INT10G8LR56
Brand: Garland Pages: 30
Idis DR-8400 Installation Manual preview
DR-8400
Brand: Idis Pages: 31
IEI Technology PUZZLE-IN003B User Manual preview
PUZZLE-IN003B
Brand: IEI Technology Pages: 86
Dahua Technology Lite N42B1P Series Quick Start Manual preview
Lite N42B1P Series
Brand: Dahua Technology Pages: 14
XNET INS2000 Install Manual preview
INS2000
Brand: XNET Pages: 17
Keithley 7011-C Instruction Manual preview
7011-C
Brand: Keithley Pages: 98
Kontron 50099 067 User Manual preview
50099 067
Brand: Kontron Pages: 42
Moxa Technologies PT-7710 Series Hardware Installation Manual preview
PT-7710 Series
Brand: Moxa Technologies Pages: 2
Enterasys Enterasys Matrix 2G4082-25 Hardware Installation Manual preview
Enterasys Matrix 2G4082-25
Brand: Enterasys Pages: 58
AMX NXA-ENET8POE Installation Manual preview
NXA-ENET8POE
Brand: AMX Pages: 2

Brands by name

Popular brands

Load more brands