manualshive.com logo in svg

Cisco 901, Command Reference Manual

The Cisco 901 Installation Manual is a comprehensive guide for setting up and configuring your Cisco 901 product. This manual is available for free download from our website, ensuring a hassle-free experience. Get your hands on the detailed manual for the Cisco 901 at manualshive.com.

Share
Download
background image

1-190

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1      CLI Command Reference

  show xconnect

You can use the 

show xconnect all

 command output to help determine the appropriate steps to 

troubleshoot an xconnect configuration problem. More specific information about a particular type of 
xconnect can be displayed using the commands listed in the Related Commands table. 

Examples

The following example shows 

show xconnect all

 command output in the brief (default) display format. 

The output shows information about the interfaces and VCs that have been configured to transport 
various Layer 2 packets on the router. 

Router#

 show xconnect all

Legend: XC ST=Xconnect State, S1=Segment1 State, S2=Segment2 State

UP=Up, DN=Down, AD=Admin Down, IA=Inactive, NH=No Hardware 

XC ST     Segment 1  S1 Segment 2 S2

ST     Segment 1                         S1 Segment 2                         S2

------+---------------------------------+--+---------------------------------+--

UP     ac   Et0/0(Ethernet)              UP mpls 10.55.55.2:1000              UP

UP     ac   Et1/0.1:200(Eth VLAN)        UP mpls 10.55.55.2:5200              UP

IA pri ac   Et1/0.2:100(Eth VLAN)        UP ac   Et2/0.2:100(Eth VLAN)        UP

UP sec ac   Et1/0.2:100(Eth VLAN)        UP mpls 10.55.55.3:1101              UP

Table 1-12

 describes the significant fields shown in the display.

The following example shows 

show xconnect all

 command output in the detailed display format: 

Table 1-12

show xconnect all Field Descriptions

Field

Description

XC ST 

•

State of the xconnect attachment circuit or PW. Valid states are:

•

UP—The xconnect attachment circuit or PW is up. Both segment 1 and 
segment 2 must be up for the xconnect to be up. 

•

DN—The xconnect attachment circuit or PW is down. Either segment 1, 
segment 2, or both segments are down. 

•

IA—The xconnect attachment circuit or PW is inactive. This state is valid 
only when PW redundancy is configured. 

•

NH—One or both segments of this xconnect no longer has the required 
hardware resources available to the system. 

Segment 1

or

Segment 2

Information about the type of xconnect, the interface type, and the IP address the 
segment is using. Types of xconnects are: 

•

ac—Attachment circuit. 

•

pri ac—Primary attachment circuit. 

•

sec ac—Secondary attachment circuit. 

•

mpls—Multiprotocol Label Switching. 

•

l2tp—Layer 2 Tunnel Protocol. 

S1 

or 

S2 

State of the segment. Valid states are:

•

UP—The segment is up. 

•

DN—The segment is down. 

•

AD—The segment is administratively down. 

Summary of Contents for 901



























































































































































































































Reviews:

No comments

Related manuals for 901

3onedata IES615-2D Series Quick Installation Manual preview
IES615-2D Series
Brand: 3onedata Pages: 3
3One data 7212 User Manual preview
7212
Brand: 3One data Pages: 5
3onedata IEM615 Series Hardware User Manual preview
IEM615 Series
Brand: 3onedata Pages: 33
A-Link WNAP4G Quick Installaion Manual preview
WNAP4G
Brand: A-Link Pages: 6
Salusfin SF-930EU User'S Installation Manual preview
SF-930EU
Brand: Salusfin Pages: 6
Galaxy Hunter Series Quick Start Manual preview
Hunter Series
Brand: Galaxy Pages: 30
3Com EtherLink 3C905C-TX User Manual preview
EtherLink 3C905C-TX
Brand: 3Com Pages: 96
Intercoax IXWB-450 Quick Start Manual preview
IXWB-450
Brand: Intercoax Pages: 2
Quidway S3000-EI Series Operation Manual preview
S3000-EI Series
Brand: Quidway Pages: 16
ADTRAN Express L128FP User Manual preview
Express L128FP
Brand: ADTRAN Pages: 161
DPS KDA 864 User Manual preview
KDA 864
Brand: DPS Pages: 57
Dialogic IP Board IPT10000C Quick Install Card preview
IP Board IPT10000C
Brand: Dialogic Pages: 2
Doro GW7001 Quick Installation Manual preview
GW7001
Brand: Doro Pages: 50
Tripp Lite N201-007-YW Specification Sheet preview
N201-007-YW
Brand: Tripp Lite Pages: 2
Hanwha Techwin Wisenet PRN-6400DB4 User Manual preview
Wisenet PRN-6400DB4
Brand: Hanwha Techwin Pages: 125
Synology DiskStation Series Upgrade Installation Instructions preview
DiskStation Series
Brand: Synology Pages: 6
QNAP QSW-3216R-8S8T Quick Installation Manual preview
QSW-3216R-8S8T
Brand: QNAP Pages: 11
Billion BiPAC 7404VGO Specifications preview
BiPAC 7404VGO
Brand: Billion Pages: 2

Brands by name

Popular brands

Load more brands