Cisco 901 Command Reference Manual Download Page 193 | Manualshive

Page: 193 / 218

background image

1-179

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1 CLI Command Reference

show policy-map interface

show policy-map interface

To display the statistics and the configurations of the input and output policies that are attached to an
interface, use the

show policy-map interface

command in user EXEC or privileged EXEC mode.

show policy-map interface

[

type access-control

]

type number

[

vc

[

vpi

/

]

vci

] [

dlci

dlci

]

[

input

|

output

]

Syntax Description

type

Type of interface or subinterface whose policy configuration is to be
displayed.

number

Port, connector, or interface card number.

vc

(Optional) For ATM interfaces only, shows the policy configuration for a
specified PVC.

vpi

/

(Optional) ATM network virtual path identifier (VPI) for this permanent
virtual circuit (PVC).

The

vpi

and

vci

arguments cannot both be set to 0; if one is 0, the other

cannot be 0.

The absence of both the forward slash (

/

) and a

vpi

value defaults the

vpi

value to 0. If this value is omitted, information for all virtual circuits (VCs)
on the specified ATM interface or subinterface is displayed.

vci

(Optional) ATM network virtual channel identifier (VCI) for this PVC. This
value ranges from 0 to 1 less than the maximum value set for this interface
by the

atm vc-per-vp

command. Typically, the lower values 0 to 31 are

reserved for specific traffic (F4 Operation, Administration, and
Maintenance [OAM], switched virtual circuit [SVC] signaling, Integrated
Local Management Interface [ILMI], and so on) and should not be used.

The VCI is a 16-bit field in the header of the ATM cell. The VCI value is
unique only on a single link, not throughout the ATM network, because it
has local significance only.

The

vpi

and

vci

arguments cannot both be set to 0; if one is 0, the other

cannot be 0.

dlci

(Optional) Indicates a specific PVC for which policy configuration will be
displayed.

dlci

(Optional) A specific data-link connection identifier (DLCI) number used
on the interface. Policy configuration for the corresponding PVC will be
displayed when a DLCI is specified.

input

(Optional) Indicates that the statistics for the attached input policy will be
displayed.

output

(Optional) Indicates that the statistics for the attached output policy will be
displayed.

slot

(ATM shared port adapter only) Chassis slot number. See the appropriate
hardware manual for slot information. For SIPs, see the platform-specific
SPA hardware installation guide or the corresponding “Identifying Slots and
Subslots for SIPs and SPAs” topic in the platform-specific SPA software
configuration guide.

«
...
191
192
193
194
195
...
»

Summary of Contents for 901



























































































































































































































Reviews:

No comments

Related manuals for 901

Professional Series

Brand: PACOM Pages: 15

Brand: Wattle Pages: 6

Brand: Baicells Pages: 8

SmartSwitch Router

Brand: Cabletron Systems Pages: 338

Brand: Observint Pages: 11

Brand: A10 Pages: 52

Brand: BSS Audio Pages: 20

Brand: H3C Pages: 12

Brand: Net to Net Technologies Pages: 4

IBOX-BAC Series

Brand: IntesisBox Pages: 2

WRT54GR - Wireless-G Broadband Router

Brand: Linksys Pages: 81

IMACS Network Device

Brand: Zhone Pages: 114

301297U - 1TB Ethernet Disk XP Embedded Network Attached...

Brand: LaCie Pages: 67

IP-Logic ZIG-IPPRO-RX

Brand: Zigen Pages: 4

Brand: 2N Telekomunikace Pages: 67

Brand: ADTRAN Pages: 4

Brand: Supero Pages: 54

Brand: R.V.R. Elettronica Pages: 171

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands