Cisco 901 Command Reference Manual Download Page 155 | Manualshive

Page: 155 / 218

background image

1-141

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1 CLI Command Reference

shape (percent)

shape (percent)

To specify average or peak rate traffic shaping on the basis of a percentage of bandwidth available on an
interface, use the

shape

command in policy-map class configuration mode. To remove traffic shaping,

use the

no

form of this command.

shape

{

average

}

percent

percentage

[

sustained-burst-in-msec

ms

] [

be

excess-burst-in-msec

ms

]

[

bc

committed-burst-in-msec

ms

]

no shape

{

average

}

percent

percentage

[

sustained-burst-in-msec

ms

] [

be

excess-burst-in-msec

ms

] [

bc

committed-burst-in-msec

ms

]

Syntax Description

Command Default

The default bc and be is 4 ms.

Command Modes

Policy-map class configuration (config-pmap-c)

Command History

Usage Guidelines

Committed Information Rate

This command calculates the committed information rate (CIR) on the basis of a percentage of the
available bandwidth on the interface. Once a policy map is attached to the interface, the equivalent CIR
value in bits per second (bps) is calculated on the basis of the interface bandwidth and the percent value
entered with this command. The

show policy-map interface

command can then be used to verify the

CIR bps value calculated.

average

Specifies average rate traffic shaping.

percent

Specifies that a percent of bandwidth will be used for either the average
rate traffic shaping or peak rate traffic shaping.

percentage

Specifies the bandwidth percentage. Valid range is a number from 1
to 100.

sustained-burst-in-msec

(Optional) Sustained burst size used by the first token bucket for policing
traffic. Valid range is a number from 4 to 200.

ms

(Optional) Indicates that the burst value is specified in milliseconds (ms).

be

(Optional) Excess burst (be) size used by the second token bucket for
policing traffic.

excess-burst-in-msec

(Optional) Specifies the be size in milliseconds. Valid range is a number
from 0 to 200.

bc

(Optional) Committed burst (bc) size used by the first token bucket for
policing traffic.

committed-burst-in-msec

(Optional) Specifies the bc value in milliseconds. Valid range is a number
from 1 to 2000.

Release

Modification

15.1(2)SNG

Support for this command was introduced on the Cisco ASR 901 router.

«
...
153
154
155
156
157
...
»

Summary of Contents for 901



























































































































































































































Reviews:

No comments

Related manuals for 901

Brand: Queclink Pages: 9

Brand: Far Tools Pages: 24

Brand: Kanguru Pages: 13

Brand: Baicells Pages: 10

Brand: axing Pages: 4

Brand: Idis Pages: 16

Ethernet MCA 10/100 Adapter

Brand: Olicom Pages: 88

Brand: Doro Pages: 50

Brand: Lanner Pages: 99

Brand: Hama Pages: 7

Brand: Belkin Pages: 42

Brand: WatchNet Pages: 2

Brand: Intercel Pages: 17

Brand: Generic Pages: 51

Brand: Cambium Networks Pages: 99

Business in a Box BIB NextGen

Brand: AT&T Pages: 9

Brand: Costar Pages: 14

Brand: Acer Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands