Cisco 901 Command Reference Manual Download Page 172

Page: 172 / 218

1-158

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1 CLI Command Reference

show interfaces rep

Examples

This is sample output from the

show interface rep

command:

Switch #

show interface rep

Interface Seg-id

Type

LinkOp

Role

---------------------- ------ ------------ ----------- ----

GigabitEthernet 0/1

Primary Edge TWO_WAY

Open

GigabitEthernet

0/2

1 Edge

TWO_WAY Open

This is sample output from the

show interface rep

command when the edge port is configured to have

no REP neighbor. Note the asterisk (*) next to

Primary Edge

Router#

show interface rep

Interface Seg-id Type LinkOp Role

---------------------- ------ -------------- ----------- ----

GigabitEthernet0/1 2 TWO_WAY Open

GigabitEthernet0/2 2 Primary Edge* TWO_WAY Open

This is sample output from the

show interface rep

command when external neighbors are not

configured:

Switch #

show interface rep

Interface Seg-id

Type

LinkOp

Role

---------------------- ------ ------------ ----------- ----

GigabitEthernet0/1 1

NO_NEIGHBOR

FailNoNbr

GigabitEthernet0/2 2

NO_NEIGHBOR

FailLogOpen

This is sample output from the

show interface rep detail

command for a specified interface:

Switch #

show interface gigabitethernet0/2 rep detail

GigabitEthernet0/2 REP enabled

Segment-id: 1 (Segment)

PortID: 00030019E85BDD00

Preferred flag: No

Operational Link Status: INIT_DOWN

Current Key: 00000000000000000000

Port Role: Fail

Blocked VLAN: 1-4094

Admin-vlan: 1

Preempt Delay Timer: disabled

LSL Ageout Timer: 5000 ms

Configured Load-balancing Block Port: 1234567890123456

Configured Load-balancing Block VLAN: 1-4094

STCN Propagate to: none

LSL PDU rx: 0, tx: 0

HFL PDU rx: 0, tx: 0

BPA TLV rx: 0, tx: 0

BPA (STCN, LSL) TLV rx: 0, tx: 0

BPA (STCN, HFL) TLV rx: 0, tx: 0

EPA-ELECTION TLV rx: 0, tx: 0

EPA-COMMAND TLV rx: 0, tx: 0

EPA-INFO TLV rx: 0, tx: 0

Related Commands

Command

Description

repsegment

Enables REP on an interface and assigns a segment ID. This command is also
used to configure a port as an edge port, a primary edge port, or a preferred
port.

show reptopology

[

detail

]

Displays information about all ports in the segment, including which one was
configured and selected as the primary edge port.

Summary of Contents for 901



























































































































































































































Search results

Summary of Contents for 901

Reviews:

Related manuals for 901

Brands by name

Popular brands

Cisco 901, Command Reference Manual

Search results

Summary of Contents for 901

Reviews:

Related manuals for 901

Brands by name

Popular brands