Cisco 901 Command Reference Manual Download Page 71

Page: 71 / 218

1-57

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1 CLI Command Reference

l2proto-forward

To configure the forwarding of tagged Layer 2 Control Packets and dropping of untagged layer 2 control
packets, use the

l2proto-forward

command in interface configuration mode. To delete this

configuration, use the

form of this command.

l2proto-forward tagged {cdp | dtp | lacp | lldp | stp | udld | vtp}

no l2proto-forward tagged {cdp | dtp | lacp | lldp | stp | udld | vtp}

Syntax Description

Defaults

The default behavior is to peer the untagged layer 2 control packets and drop tagged layer 2 control
packets.

Command Modes

Interface configuration (config-if)

Command History

Usage Guidelines

Use this command to forward tagged and drop untagged layer 2 control protocol packets.

Examples

The following example shows how to configure the forwarding of tagged Layer 2 Control Packets and
dropping of untagged layer 2 control packets using the

l2proto-forward

command.

Router#

configure terminal

Router#(config)

interface gigabitethernet 0/1

Router(config-if)#

l2proto-forward tagged cdp

cdp

Enables Cisco Discovery Protocol (CDP) tunneling.

dtp

Enables Dynamic Trunking Protocol (DTP) tunneling.

lacp

Enables Link Aggregration Control Protocol (LACP) tunneling.

lldp

Enables Link Layer Discovery Protocol (LLDP) tunneling.

stp

Enables Spanning Tree Protocol tunneling (STP).

udld

Enables UniDirectional Link Detection (UDLD) protocol tunneling.

vtp

Enables Vlan Trunking Protocol (VTP) tunneling.

Release

Modification

15.2(2)SNG

This command was introduced.

Summary of Contents for 901



























































































































































































































Search results

Summary of Contents for 901

Reviews:

Related manuals for 901

Brands by name

Popular brands

Cisco 901, Command Reference Manual

Search results

Summary of Contents for 901

Reviews:

Related manuals for 901

Brands by name

Popular brands