manualshive.com logo in svg

Cisco 901, Command Reference Manual

The Cisco 901 Installation Manual is a comprehensive guide for setting up and configuring your Cisco 901 product. This manual is available for free download from our website, ensuring a hassle-free experience. Get your hands on the detailed manual for the Cisco 901 at manualshive.com.

Share
Download
background image

1-160

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1      CLI Command Reference

  show ip vrf

                      

Virtual-Access4 [D] 

  

  U      2:1          Virtual-Access3

                      Virtual-Access4

Table 1-6

 describes the significant fields shown in the display. 

The following example displays detailed information about all of the VRFs configured on the router, 
including all of the VAIs associated with each VRF:

Router# 

show ip vrf detail 

VRF D; default RD 2:0; default VPNID <not set>

  Interfaces:

         Loopback2           Virtual-Access3 [D]  Virtual-Access4 [D]

  Connected addresses are not in global routing table

  Export VPN route-target communities

    RT:2:0                 

  Import VPN route-target communities

    RT:2:1                 

  No import route-map

  No export route-map

VRF U; default RD 2:1; default VPNID <not set>

  Interfaces:

    Virtual-Access3          Virtual-Access4         

  Connected addresses are not in global routing table

  No Export VPN route-target communities

  Import VPN route-target communities

    RT:2:1                 

  No import route-map

  No export route-map

Table 1-7

 describes the significant fields shown in the display.

The following example shows the interfaces bound to a particular VRF:

Router# 

show ip vrf interfaces

InterfaceIP-AddressVRFProtocol

Table 1-6

show ip vrf Field Descriptions

Field

Description

Name

Specifies the VRF name.

Default RD

Specifies the default route distinguisher.

Interface

Specifies the network interface.

Table 1-7

show ip vrf detail Field Descriptions

Field

Description

VPNID

Specifies the VPN ID assigned to the VRF.

Interfaces 

Specifies the network interfaces.

Virtual-Access

n 

[D]

Specifies the downstream VRF.

Export 

Specifies VPN route-target export communities.

Import 

Specifies VPN route-target import communities.

Summary of Contents for 901



























































































































































































































Reviews:

No comments

Related manuals for 901

Accelerated 6330-MX User Manual preview
6330-MX
Brand: Accelerated Pages: 10
Accelerated 6300-CX Customer Setup Instructions preview
6300-CX
Brand: Accelerated Pages: 4
Ubee DVW3201B User Manual preview
DVW3201B
Brand: Ubee Pages: 9
E-TOP BR486n User Manual preview
BR486n
Brand: E-TOP Pages: 76
TFortis Teleport-1 Configuration Manual preview
Teleport-1
Brand: TFortis Pages: 86
FS FS-BOX-V3 Quick Start Manual preview
FS-BOX-V3
Brand: FS Pages: 19
Eaton APS6-400 Series Installation And Operation Manual preview
APS6-400 Series
Brand: Eaton Pages: 114
Idis DR-8400 Installation Manual preview
DR-8400
Brand: Idis Pages: 31
Extron electronics PoleVault System A/V Source Inputs Specification Sheet preview
PoleVault System A/V Source Inputs
Brand: Extron electronics Pages: 4
IBM 8677 - BladeCenter Rack-mountable - Power Supply Planning And Installation Manual preview
8677 - BladeCenter Rack-mountable - Power Supply
Brand: IBM Pages: 126
TP-Link Archer VR500vd Installation Manual preview
Archer VR500vd
Brand: TP-Link Pages: 7
Ozenda AR4505GW Instruction Manual preview
AR4505GW
Brand: Ozenda Pages: 116
TP-Link TL-MR3620 Installation Manual preview
TL-MR3620
Brand: TP-Link Pages: 2
XAVI Technologies Corp. X7822r User Manual preview
X7822r
Brand: XAVI Technologies Corp. Pages: 63
Hawking H-CF30W Quick Installation Manual preview
H-CF30W
Brand: Hawking Pages: 21
ORiNG TGXPS-1080-M12-MV Series Quick Installation Manual preview
TGXPS-1080-M12-MV Series
Brand: ORiNG Pages: 2
Riverbed SteelCentral NetExpress 470 Upgrade And Maintenance Manual preview
SteelCentral NetExpress 470
Brand: Riverbed Pages: 140
Calix GigaSpire BLAST u4hm Installation Manual preview
GigaSpire BLAST u4hm
Brand: Calix Pages: 45

Brands by name

Popular brands

Load more brands