manualshive.com logo in svg

Cisco 901, Command Reference Manual

The Cisco 901 Installation Manual is a comprehensive guide for setting up and configuring your Cisco 901 product. This manual is available for free download from our website, ensuring a hassle-free experience. Get your hands on the detailed manual for the Cisco 901 at manualshive.com.

Share
Download
background image

1-50

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1      CLI Command Reference

  interface vlan

interface vlan 

To create a dynamic Switch Virtual Interface (SVI), use the 

interface vlan

 command in global 

configuration mode.

interface vlan 

vlanid

no interface vlan 

vlanid

 

Syntax Description

Command Default

None

Command Modes

Global configuration 

Command History

Usage Guidelines

SVIs are created the first time that you enter the 

interface vlan

 

vlanid

 command for a particular VLAN. 

The vlanid value corresponds to the VLAN tag that is associated with the data frames on an Inter-Switch 
Link (ISL), the 802.1Q-encapsulated trunk, or the VLAN ID that is configured for an access port. A 
message displays whenever you create a new VLAN interface, so that you can check if you entered the 
correct VLAN number.

If you delete an SVI by entering the 

no

 

interface vlan

 

vlanid

 command, the associated initial domain 

part (IDP) pair is forced into an administrative down state and is marked as deleted. The deleted interface 
will not be visible in the show interface command.

You can reinstate a deleted SVI by entering the 

interface vlan

 

vlanid

 command for the deleted interface. 

The interface comes back up, but much of the previous configuration is gone.

Examples

The following example shows the output when you enter the interface vlan vlanid command for a new 
VLAN number:

Router(config)# 

interface vlan 23

% Creating new VLAN interface.

vlanid

Unique VLAN ID number (1 to 4094) used to create or access a VLAN. 

Release

Modification

15.1(2)SNG

Support for this command was introduced on the Cisco ASR 901 router.

Summary of Contents for 901



























































































































































































































Reviews:

No comments

Related manuals for 901

D-Link AirPlus DWL-810 Owner'S Manual preview
AirPlus DWL-810
Brand: D-Link Pages: 25
Magnat Audio MC 200 Faq preview
MC 200
Brand: Magnat Audio Pages: 2
Black Box LT2060A Manual preview
LT2060A
Brand: Black Box Pages: 37
American Megatrends StorTrends 1312-P Specifications preview
StorTrends 1312-P
Brand: American Megatrends Pages: 2
NA DigiNet 416 User Manual preview
DigiNet 416
Brand: NA Pages: 22
Buffalo LinkStation Quick Setup Manual preview
LinkStation
Brand: Buffalo Pages: 2
ProCurve J8454A Quick Start Manual preview
J8454A
Brand: ProCurve Pages: 2
SurfControl 509-8629-00 Setup Manual preview
509-8629-00
Brand: SurfControl Pages: 2
Ubiquiti EdgeSwtch 5XP Quick Start Manual preview
EdgeSwtch 5XP
Brand: Ubiquiti Pages: 13
TP-Link VIGI NVR1004H-4P Quick Installation Manual preview
VIGI NVR1004H-4P
Brand: TP-Link Pages: 2
Dahua Technology NVR2104/2108HS-W-4KS2 1U User Manual preview
NVR2104/2108HS-W-4KS2 1U
Brand: Dahua Technology Pages: 363
3Com NETBuilder SI Using Manual preview
NETBuilder SI
Brand: 3Com Pages: 212
Multiplex MULTIflight Stick Operating Instructions Manual preview
MULTIflight Stick
Brand: Multiplex Pages: 10
Chaparral FS1310 User Manual preview
FS1310
Brand: Chaparral Pages: 96
RouterBOARD OmniTik UPA-5HnD Quick Setup Manual And Warranty Information preview
OmniTik UPA-5HnD
Brand: RouterBOARD Pages: 4
Airlinkplus UG-ASW232-1103 User Manual preview
UG-ASW232-1103
Brand: Airlinkplus Pages: 24
TDT VR2020 Series Initial Start-Up Manual preview
VR2020 Series
Brand: TDT Pages: 8
LaCie 301269U - Ethernet Disk Mini Home Edition 500 GB Network Attached Storage Hard... User Manual preview
301269U - Ethernet Disk Mini Home Edition 500 GB Network Attached Storage Hard...
Brand: LaCie Pages: 74

Brands by name

Popular brands

Load more brands