manualshive.com logo in svg

Cisco 901, Command Reference Manual

The Cisco 901 Installation Manual is a comprehensive guide for setting up and configuring your Cisco 901 product. This manual is available for free download from our website, ensuring a hassle-free experience. Get your hands on the detailed manual for the Cisco 901 at manualshive.com.

Share
Download
background image

1-68

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1      CLI Command Reference

  negotiation

negotiation

To enable advertisement of speed, duplex mode, and flow control on a Gigabit Ethernet interface, use 
the

 negotiation 

command in interface configuration mode. To disable automatic negotiation, use the 

no 

negotiation auto

 command.

negotiation 

{

auto

}

no negotiation auto

Syntax Description

Command Default

Autonegotiation is enabled.

Command Modes

Interface configuration (config-if)

Command History

Usage Guidelines

The 

negotiation auto 

command is used instead of the 

duplex

 and 

speed

 commands (which are used on 

Ethernet to automatically configure the duplex and speed settings of the interfaces.

The 

no negotiation auto

 command is used to disable the autonegotiation. If the speed is set to 1000 

Mbps and full-duplex is set for the Gigabit Ethernet interface in small form-factor pluggable (SFP) 
mode, then the autonegotiation is disabled (forced mode) using the 

no negotiation auto

 command. 

Related Commands

auto

Enables the autonegotiation protocol to configure the speed, duplex, and 
automatic flow control of the Gigabit Ethernet interface. This is the default.

Release

Modification

15.1(2)SNG

Support for this command was introduced on the Cisco ASR 901 router.

Command

Description

show interfaces gigabitethernet

Displays information about the Gigabit Ethernet interfaces.

Summary of Contents for 901



























































































































































































































Reviews:

No comments

Related manuals for 901

Supero 6027R-E1R12N User Manual preview
6027R-E1R12N
Brand: Supero Pages: 112
Riverbed SteelCentral NetExpress Installation Manual preview
SteelCentral NetExpress
Brand: Riverbed Pages: 38
Paradyne MIM-4000F Installation Instructions Manual preview
MIM-4000F
Brand: Paradyne Pages: 6
AIC SB401-MN User Manual preview
SB401-MN
Brand: AIC Pages: 88
Paradyne JetFusion 2100 Series User Manual preview
JetFusion 2100 Series
Brand: Paradyne Pages: 296
Teldat G1N Installation Manual preview
G1N
Brand: Teldat Pages: 23
Ubiquiti EdgeRouter X Quick Start Manual preview
EdgeRouter X
Brand: Ubiquiti Pages: 20
Axis P1355-E User Manual preview
P1355-E
Brand: Axis Pages: 64
SHOWTEC LED Operator 4 Manual preview
LED Operator 4
Brand: SHOWTEC Pages: 15
Premio FlacheSAN2-D5 Quick Manual preview
FlacheSAN2-D5
Brand: Premio Pages: 2
CalAmp Sentry 4G 2500 User Manual preview
Sentry 4G 2500
Brand: CalAmp Pages: 52
Apposite Technologies Linktropy MINI-G User Manual preview
Linktropy MINI-G
Brand: Apposite Technologies Pages: 57
Meridian Meridian 1 Option 11C Mini Technical Reference Manual preview
Meridian 1 Option 11C Mini
Brand: Meridian Pages: 546
Hirschmann MM2-2FXM3/2TX1 Description And Operating Instructions preview
MM2-2FXM3/2TX1
Brand: Hirschmann Pages: 8
H3C RA5100 Manual preview
RA5100
Brand: H3C Pages: 11
Tame Parent box User Manual preview
Parent box
Brand: Tame Pages: 55
OneAccess 1645 Installation Manual preview
1645
Brand: OneAccess Pages: 54
F5 BIG-IP 3900 Manual preview
BIG-IP 3900
Brand: F5 Pages: 48

Brands by name

Popular brands

Load more brands