Cisco 901 Command Reference Manual Download Page 196

Page: 196 / 218

1-182

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1 CLI Command Reference

show ptp port running detail

To display the running details of the PTP port, use the

show ptp port running detail

command.

show ptp port running detail

Syntax Description

This command has no arguments or keywords.

Command Modes

Privileged EXEC (#)

Command History

Usage Guidelines

This command is used to display running details of the PTP port.

Note

Accuracy and log variance are not displayed for the telecom profile since the fields are not required for
selecting the best master.

Examples

This example shows the output from

show ptp port running detail

command on a

Cisco ASR 901 router:

Router#

show ptp port running detail

PORT [SLAVE] CURRENT PTP MASTER PORT

Protocol Address: 10.10.10.10

Clock Identity: 0xE4:D3:F1:FF:FE:22:FD:B8

PORT [SLAVE] PREVIOUS PTP MASTER PORT

Protocol Address: 30.30.30.30

Clock Identity: 0xE0:2F:6D:FF:FE:74:EF:70

Reason:

PORT [SLAVE] LIST OF PTP MASTER PORTS

LOCAL PRIORITY 0

Protocol Address: 10.10.10.10

Clock Identity: 0xE4:D3:F1:FF:FE:22:FD:B8

PTSF Status:

Alarm In Stream:

Clock Stream Id: 0

Priority1: 128

Priority2: 128

Class: 84

Accuracy: Unknown <===========

Offset (log variance): 0 <==========

Steps Removed: 0

Release

Modification

15.4(1)S

This command was introduced on the Cisco ASR 901 Series Aggregation
Services Routers.

Summary of Contents for 901



























































































































































































































Search results

Summary of Contents for 901

Reviews:

Related manuals for 901

Brands by name

Popular brands

Cisco 901, Command Reference Manual

Search results

Summary of Contents for 901

Reviews:

Related manuals for 901

Brands by name

Popular brands