Cisco 901 Command Reference Manual Download Page 52 | Manualshive

Page: 52 / 218

background image

1-38

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1 CLI Command Reference

duplex

Caution

Changing the interface speed and duplex mode configuration might shut down and reenable the interface
during the reconfiguration.

Table 1-2

describes the interface behavior for different combinations of the

duplex

and

speed

command

settings. The specified

duplex

command configured with the specified

speed

command produces the

resulting system action.

Note

If you need to force an interface port to operate with certain settings and therefore disable
autonegotiation, you must be sure that the remote link is configured with compatible link settings for
proper transmission. This includes support of flow control on the link.

Examples

The following example shows how to configure duplex half operation:

Router(config)#

interface gigabitethernet0/0

Router(config-if)#

duplex half

Related Commands

Table 1-2

Relationship Between duplex and speed Commands

duplex Command

speed Command

Resulting System Action

duplex half

speed 10

Forces 10-Mbps and half-duplex operation, and
disables autonegotiation on the interface.

duplex full

speed 10

Forces 10-Mbps and full-duplex operation, and
disables autonegotiation on the interface.

duplex half

speed 100

Forces 100-Mbps and half-duplex operation, and
disables autonegotiation on the interface.

duplex full

speed 100

Forces 100-Mbps and full-duplex operation, and
disables autonegotiation on the interface.

duplex full

speed 1000

Forces 1000-Mbps and full-duplex operation,
and disables autonegotiation on the interface
(Gigabit Ethernet only).

Command

Description

interface

Selects an interface to configure and enters interface configuration
mode.

interface gigabitethernet

Selects a particular Gigabit Ethernet interface for configuration.

show controllers

Displays information that is specific to the hardware on a module.

show controllers
gigabitethernet

Displays Gigabit Ethernet interface information, transmission statistics
and errors, and applicable MAC destination address and VLAN
filtering tables.

show interfaces

Displays traffic that is seen by a specific interface.

show interfaces
gigabitethernet

Displays information about the Gigabit Ethernet interfaces.

speed

Sets the port speed for a Fast Ethernet interface.

«
...
50
51
52
53
54
...
»

Summary of Contents for 901



























































































































































































































Reviews:

No comments

Related manuals for 901

Brand: 3Com Pages: 48

SISPM1040-582-LRT

Brand: Lantronix Pages: 2

Brand: Lantronix Pages: 7

Maestro E220 Series

Brand: Lantronix Pages: 25

Brand: Ubiquiti Pages: 50

Brand: H3C Pages: 77

Brand: Intellinet Pages: 2

Brand: NA Pages: 22

RabbitCore RCM4400W

Brand: Rabbit Pages: 126

ControlPoint 2000

Brand: 4Home Pages: 20

Speedway Revolution

Brand: impinj Pages: 60

Brand: NetComm Pages: 65

Brand: Draytek Pages: 17

Brand: Moeller Pages: 4

AirBridge WBC502

Brand: NETGEAR Pages: 7

Brand: Nokia Pages: 67

Brand: Nokia Pages: 10

Brand: MikroTik Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands