Cisco 901 Command Reference Manual Download Page 53

Page: 53 / 218

1-39

Cisco ASR 901 Aggregation Services Router Command Reference Guide

OL-26031-07

Chapter 1 CLI Command Reference

efd notify g8032

To notify G.8032 of failures, use the

efd notify g8032

command in the Ethernet CFM service

configuration mode. To remove this configuration, use the

form of this command.

efd notify g8032

no efd notify g8032

Syntax Description

Command Default

Monitoring and notifying G.8032 for failures is disabled.

Command Modes

Ethernet CFM service configuration (config-ecfm-srv) #

Command History

Usage Guidelines

When G8032 ring links are monitored by CFM sessions, use the

efd notify g8032

command under CFM

service configuration to notify G8032 of failures, if any.

Examples

The following example shows how to use the

efd notify g8032

command:

Router #

configure terminal

Router(config)#

ethernet cfm global

Router(config)#

ethernet cfm domain MD4 level 4

Router(config-ecfm)#

service 1 evc evc1 vlan 99 direction down

Router(config-ecfm-srv)#

continuity-check

Router(config-ecfm-srv)#

continuity-check interval 3.3ms

Router(config-ecfm-srv)#

offload sampling 6000

Router(config-ecfm-srv)#

efd notify g8032

Related Commands

efd notify g8032

Monitors and notifies G.8032 of failures.

Release

Modification

15.4(3)S

This command was introduced on the Cisco ASR 901 Routers.

Command

Description

ethnernet cfm global

Enables Ethernet CFM globally on a router.

ethernet cfm domain
level

Defines a CFM maintenance domain at a particular maintenance level.

continuity-check

Enables sending and receiving of continuity check messages.

offload sampling

Configures the sampling rate for the offloaded CFM session.

Summary of Contents for 901



























































































































































































































Search results

Summary of Contents for 901

Reviews:

Related manuals for 901

Brands by name

Popular brands

Cisco 901, Command Reference Manual

Search results

Summary of Contents for 901

Reviews:

Related manuals for 901

Brands by name

Popular brands