8
8
8-261
8-261
Service Mode > SORTER > ADJUST
Service Mode > SORTER > ADJUST
SORTER > ADJUST
ST-ALG1
Adj Stacker A4 size align pstn: Fin-C1
Lv.1 Details
To adjust the A4 size paper alignment position.
As the value is incremented by 1, the travel length of the Alignment
Plate is increased by 0.42mm.
Use case
When misalignment occurs in A4 size paper
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range
-10 to 10
Unit
mm
Default value
0
ST-ALG2
Adj Stacker LTR size align pstn: Fin-C1
Lv.1 Details
To adjust the LTR size paper alignment position.
As the value is incremented by 1, the travel length of the Alignment
Plate is increased by 0.42mm.
Use case
When misalignment occurs in LTR size paper
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range
-10 to 10
Unit
mm
Default value
0
STP-F3
Adj A4R frt stpl pstn (<45 deg): Fin-C1
Lv.1 Details
To adjust the one front staple position on the A4R size paper.
As the value is incremented by 1, the staple position moves to the
rear side by 0.49mm.
Use case
When misalignment occurs at the front staple position on A4R size
paper
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range
-6 to 6
Unit
mm
Default value
0
STP-F4
Adj LTRR frt stpl pstn (<45 deg): Fin-C1
Lv.1 Details
To adjust the one front staple position on the LTRR size paper.
As the value is incremented by 1, the staple position moves to the
rear side by 0.49mm.
Use case
When misalignment occurs at the front staple position on LTRR size
paper
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range
-6 to 6
Unit
mm
Default value
0
SORTER > ADJUST
STP-R3
Adj A4R rear stpl pstn (<45 deg): Fin-C1
Lv.1 Details
To adjust the one rear staple position on the A4R size paper.
As the value is incremented by 1, the staple position moves to the
rear side by 0.49mm.
Use case
When misalignment occurs at the rear staple position on A4R size
paper
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range
-6 to 6
Unit
mm
Default value
0
STP-R4
Adj LTRRL rear stpl pstn(<45 deg):Fin-C1
Lv.1 Details
To adjust the one rear staple position on the LTRR size paper.
As the value is incremented by 1, the staple position moves to the
rear side by 0.49mm.
Use case
When misalignment occurs at the rear staple position on LTRR size
paper
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range
-6 to 6
Unit
mm
Default value
0
SW-UP-RL
Adj of Swing Roller falling pstn: Fin-C1
Lv.1 Details
To adjust the Swing Roller fall position.
As the value is incremented by 1, the Swing Roller fall position
moves downward by 0.2mm.
Use case
When paper fails to be transported to the Processing Tray and
misalignment occurs
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range
-17 to 33
Unit
mm
Default value
0
PUN-V-RG
[Not used]
PRCS-RET
Adj Process Tray return amount: Fin-C1
Lv.1 Details
To adjust the pull-back amount of the paper on the Processing Tray.
As the value is incremented by 1, the pull-back amount is decreased
by 1.4mm.
Use case
When the paper is bent in the Processing Tray
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
0 to 5
Unit
mm
Default value
0