Canon imageFORMULA DR-G2140 Service Manual Download Page 78

Page: 78 / 196

3-16

CHAPTER 3 DISASSEMBLY & REASSEMBLY

8. U-turn Upper Roller

There are pre U-turn upper roller and 2 U-

turn upper rollers in U-turn section of the up-

per unit.

1) Remove the entire upper unit.

(Page 3-19)

2) Remove 6 screws



(3 on both sides,

M3-TP head, round tip) and remove the U-

turn guide



Figure 3-318

3) Open the end of both bearing holders



and while unhooking the fitting parts, re-

move the pre U-turn upper roller



and 2

U-turn upper rollers



Note:

The roller with a wider roller rubber is a

pre U-turn upper roller.

Figure 3-319

Note:

Refer to “Pull-in Upper Roller” for details
of the subsequent procedure and pre-

cautions.

(Page 3-12)

9. Eject Follower Roller

1) Remove the eject tray unit.

(Page 3-7)

2) While unhooking 2 pairs of the fitting

parts



one at a time, pull out the eject

follower roller



upward.

Note:

Since the fitting parts are secure, pull

the roller out carefully to prevent dam-

age to it.

Do not lose the coil springs



Figure 3-320



Notes on assembling

Set the roller shaft with the D-cut

shapes



down, and assemble the roller

during pushing coil springs.

Figure 3-321

Summary of Contents for imageFORMULA DR-G2140





































































































































































































Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews:

Canon imageFORMULA DR-G2140, Service Manual, Page: 78 / 196

Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews: