Canon imageFORMULA DR-G2140 Service Manual Download Page 165

Page: 165 / 196

5-31

CHAPTER 5 TROUBLESHOOTING

9. Others

This is used to check operation of the

other sensors and functions.

It is shown the display screen and list of

items below.

Figure 5-259

No.

Display



Formal sensor name

Exit sensor



Exit sensor

Double feed sensor



Double feed sensor

TrayHP



Tray home sensor

Door sensor



Door sensor

PickHP



Pickup roller sensor

Image HP Bottom



Shading sensor (back)

Image HP Top



Shading sensor (front)

FeedMotorLock



(This is not necessary in market)

Table 5-206

D. Firmware

There are two methods for updating the

firmware: One is to select and execute pre-

registered firmware, and the other is to select

and execute firmware saved on the computer.

The methods using pre-registration makes it

possible to store all of the firmware within the

same folder and attach comments to firmware,

and is easy to manage.

Figure 5-260

Note: For details on firmware updates, refer

also to the separately issued service in-

formation.

Summary of Contents for imageFORMULA DR-G2140





































































































































































































Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews:

Canon imageFORMULA DR-G2140, Service Manual, Page: 165 / 196

Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews: