Canon imageFORMULA DR-G2140 Service Manual Download Page 179

Page: 179 / 196

5-45

CHAPTER 5 TROUBLESHOOTING

3. Scanning Does Not Start

Note:

While error messages is displayed, scanning may not start. Clear the error.

Cause/Faulty

Locations

Step

Check Item

Result

Action

System

Does a resetting this
machine and computer
fix the problem?

YES

End.

Software

Does  a  reinstalling  the
scanner  driver  and  ap-
plication  fix  the  prob-
lem?

YES

End.

Connection of the
connector

Are the motor and sen-
sor connectors con-
nected correctly?

Connect the connectors
correctly.

Drive

transmission

system

Is the transmission sys-
tem of the motors nor-
mal?
Are parts such as gears
and belts normal?

Attach the parts correctly.
Replace the parts.

Motors

Is the operation normal
when you perform an
operation check with the
service mode?

Check the cable connec-
tions. Replace the parts.

Sensors

Is the operation normal
when you perform an
operation check with the
service mode?

Check the cable connec-
tion, and the attachment of
sensors, sensor levers and
light guide. Replace the
parts.

Control PCB
Main drive PCB
Sub-drive PCB

Was the problem solved
by replacing each PCB?

YES

End.

Table 5-404

Summary of Contents for imageFORMULA DR-G2140





































































































































































































Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews:

Canon imageFORMULA DR-G2140, Service Manual, Page: 179 / 196

Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews: