Canon imageFORMULA DR-G2140 Service Manual Download Page 74

Page: 74 / 196

3-12

CHAPTER 3 DISASSEMBLY & REASSEMBLY

3. Upper Entrance Guide

1) Open the pickup roller cover.

2) Remove 2 screws



(M3x6, self-tapping)

and 6 screws



(M3-bind head, round tip)

and remove the upper entrance guide



Figure 3-306

4. Pull-in Upper Roller

1) Remove the upper entrance guide.

(Page 3-12)

2) Open the end of both bearing holders



and while unhooking the fitting parts, re-

move the pull-in roller unit



Note:

Since the coil spring in the roller unit

may be detached, do not lose it.

The tension of this coil spring is harder
than other holders’ one. Do not mix
them.

Figure 3-307

3) Remove 2 E-rings



(1 on both sides)

and remove the bearing holder



from

the pull-in upper roller



Figure 3-308

Summary of Contents for imageFORMULA DR-G2140





































































































































































































Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews:

Canon imageFORMULA DR-G2140, Service Manual, Page: 74 / 196

Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews: