manualshive.com logo in svg

Canon imageFORMULA DR-G2140, Service Manual, Page: 131 / 196

Share
Download
Canon imageFORMULA DR-G2140 Service Manual Download Page 131

 

 

COPYRIGHT © CANON ELECTRONICS INC. 2018           CANON DR-G2140/G2110/G2090 FIRST EDITION

 

4-15

 

CHAPTER 4 INSTALLATION & MAINTENANCE 

III. MAINTENANCE 

1. User Maintenance 

A list is shown below. Refer to the “User Manual” for details. 

 [ : Cleaning, 

: Replace] 

No. 

Location/parts 

Intervals 

Details 

As 

required 

Others 

1 

Main body 

 

 

Wipe the main body with a cloth dipped 
into water and wrung tightly, then wipe 
dry. 

2 

Pickup inlet/feed path 

 

 

Using a blower, etc., remove remained 
dust and paper powder. 

3 

Pickup roller 
Feed roller 
Retard roller 

 



600,000 

sheets 

Wipe the rollers with a cloth dipped into 
water and wrung tightly, then wipe dry. 
The  expected  life  is  600,000  sheets. 
Refer to Note 2. 

4 

Separation pad 
(cover) 

 



6,000,000 

sheets

Wipe the rollers with a cloth dipped into 
water and wrung tightly, then wipe dry. 
The expected life is 6,000,000 sheets. 
Refer to Note 2. 

5 

Power plug 

 

 

Remove  dust  on  the  connecting por-
tion with the receptacle. 

6 

Reading glass 

 

 

Wipe  the  reading  glass  with  a  cloth 
dipped  into  water  and  wrung  tightly, 
then wipe dry. 

7 

Ink cartridge 

 

 

 

Perform the Head Cleaning in the user 
mode. And clean the discharge outlet 
of the ink head with soft cloth or paper 
or a cotton swab. Refer to Note 3. 

8 

Parts to which ink is  
attached 

 

 

Wipe  these  parts  with  a  cloth  dipped 
into water and wrung tightly, then wipe 
dry. 

Table 4-301 

 

Note 1: 

 

The supplied cleaning cloth is used to clean the reading glass and rollers.

 

Note 2: 

 

If the number of sheets fed with the roller exceeds 600,000 sheets, a replacement mes-
sage is displayed on the operation panel LCD and computer screen. For the separation 
pad, it is displayed at exceeding 6,000,000 sheets.

 

Note 3: 

 

If  lines  or  streaks  appear  in  the  printout,  it  can  be  corrected  by  performing  the  Head 
Cleaning. However, it does not improve printing, remove the ink cartridge and clean the 
print head.

 

 

Summary of Contents for imageFORMULA DR-G2140





































































































































































































Reviews:

No comments