Canon imageFORMULA DR-G2140 Service Manual Download Page 173

Page: 173 / 196

5-39

CHAPTER 5 TROUBLESHOOTING

H. Network

This is used to check and set the network

settings.

Figure 5-278



DHCP

Display and set the setting of DHCP. If you

get the IP address automatically using

DHCP, turn it ON.



IP Address

Display the IP Address. When the DHCP

setting is OFF, you can set it.



Subnet Mask

Display the subnet mask. When the DHCP

setting is OFF, you can set it.



Default Gateway

Display the default gateway. When the

DHCP setting is OFF, you can set it.



Mac Address

Display the Mac address of this main body.

Note:

The

“Mac Address” cannot changed in

the market.

Note:

When you change the network settings,

you have to inform to user.

Summary of Contents for imageFORMULA DR-G2140





































































































































































































Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews:

Canon imageFORMULA DR-G2140, Service Manual, Page: 173 / 196

Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews: