Canon imageFORMULA DR-G2140 Service Manual Download Page 66

Page: 66 / 196

3-4

CHAPTER 3 DISASSEMBLY & REASSEMBLY

3) Since there are bottom and front fitting

parts, remove the rear fitting part, slide

the right cover



to the bottom and front

and remove it from the main body.

Note:

Do not pull it excessively because a ca-

ble is connected to the back side.

Figure 3-204

4) Remove the cable band with lock



and

connector with lock



and remove the

right cover assembly



Figure 3-205

Note:

The right cover assembly is composed

of the right cover, right upper cover and

operation panel. Remove them if nec-

essary.

3. Operation Panel

1) Remove the right cover assembly.

(Page 3-3)

2) Remove 2 screws



(M3x8, self-tapping,

black) and remove the operation panel



and then the cable



Figure 3-206

Note:

Since the operation panel assembly is

set as a single part, do not disassem-

ble it.

Summary of Contents for imageFORMULA DR-G2140





































































































































































































Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews:

Canon imageFORMULA DR-G2140, Service Manual, Page: 66 / 196

Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews: