Canon imageFORMULA DR-G2140 Service Manual Download Page 168

Page: 168 / 196

5-34

CHAPTER 5 TROUBLESHOOTING

2. Firm Load

This method for writing firmware varies

depending on whether that firmware has al-

ready been registered or has not been regis-

tered. The operation procedures are shown

below.

Note

: Do not remove the USB cable or turn

the power OFF during loading. If the

power is turned OFF, it returns to its

original state when restarted, but this is

not guaranteed.



For registered firmware

In this mode, the file saved in the service

tool is selected and its version is upgraded.

1) Select the version to write and then select

[Version up] in middle.

Figure 5-267

2) The confirmation screen is displayed.

Select [OK].

Figure 5-268

3) Writing starts automatically and the pro-

gress screen is displayed.

Figure 5-269

4) When finished, the progress disappears

and the complete screen appears. Select

[OK].

Figure 5-270

Summary of Contents for imageFORMULA DR-G2140





































































































































































































Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews:

Canon imageFORMULA DR-G2140, Service Manual, Page: 168 / 196

Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews: