Canon imageFORMULA DR-G2140 Service Manual Download Page 157

Page: 157 / 196

CANON DR-G2140/G2110/G2090 FIRST EDITION

5-23

CHAPTER 5 TROUBLESHOOTING

3. Registration (Manual)

Registration adjustment is normally per-

formed in automatic mode [All]. This manual

adjustment is a mode that performs fine ad-

justment of the result of the automatic adjust-

ment. Note that it does not reduce variations

in the registration position.



Adjustment sheet

You can use a sheet that is printed any pat-

tern to be judged a gap of position of the

leading and trailing edges. Therefore you

can use the test sheet; TKM-0271, adjust-

ment sheet; 6Y3-6001 that is used for the

automatic adjustment, or others.



Operation Procedure

In this section, it is described a case that

adjustment value is known ready.

1) Clean feed path, rollers, and scanning

glass.

2) Place a single adjustment sheet in center

and printed side should be set to adjust-

ment side.

Make sure to set the document guides so

they are fit with the adjustment sheet to

prevent skews.

3) Select the [Edit] button.

4) As for the value to adjust, the amount of

additional change is added to the value

previously set by the automatic adjustment.

For example, add [-1.0] mm

to “Front: Top”

if you want to make the reading start of the

leading edge 1mm earlier on the front side,

or add [1.0] if you want to subtract 1mm.

Figure 5-240

5) Input the value to adjust, and click the [Ap-

ply] button.

6) Open [Scan test] tab. And select [Scan test]

button, and set the scanning conditions,

then start a scanning.

Note:

Refer to the s

ection “F. Scan Test” for

details of “Scantest”.

7) The adjustment sheet is scanned.

8) Check the scanned image to be adjusted.

Note:

Repeat the procedure again if the ad-

justments were not corrected properly.

→

0.1+1.0 = 1.1

Summary of Contents for imageFORMULA DR-G2140





































































































































































































Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews:

Canon imageFORMULA DR-G2140, Service Manual, Page: 157 / 196

Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews: