Canon imageFORMULA DR-G2140 Service Manual Download Page 124

Page: 124 / 196

4-8

CHAPTER 4 INSTALLATION & MAINTENANCE

3. Imprinter Installation Procedure

No.

Step

Details/Remarks

1 Make sure that all parts are ready.



IP drain unit



IP carriage



IP shaft



Stopper plate (2 pcs.)



Plastic retaining ring



Screw (BH, M3x6)



Caution label



IP label



Protection sheet

Note:

1) The stopper plate



is for DR-G2140

series only and protection sheet



for DR-G1130 series only to use.

2) Since the electrical contacts of the IP

carriage are exposed, handle it care-
fully to avoid damage due to static
electricity.

3) The E-ring must be press-fitted on the

one side of the IP shaft.

4) Provide an ink cartridge for operation

check. The ink cartridge is separately
sold.

2 Remove the right and left covers and the

eject tray unit.

Note:

1) Refer to “CHAPTER 3, DISASSEM-

BLY & REASSEMBLY” for details.

3 Insert the IP drain unit



into the hole on

the right side of this machine, in the di-
rection of the arrow, as far as it will go. Be
careful to orient the unit correctly. Place
the inserted tip



into the hole on the

left side of this machine.

Left side

Right side

Summary of Contents for imageFORMULA DR-G2140





































































































































































































Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews:

Canon imageFORMULA DR-G2140, Service Manual, Page: 124 / 196

Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews: