Canon imageFORMULA DR-G2140 Service Manual Download Page 100

Page: 100 / 196

3-38

CHAPTER 3 DISASSEMBLY & REASSEMBLY

17. Eject Drive Unit

1) Remove the control PCB cover.

(Page 3-3)

2) Remove the top cover.

(Page 3-6)

3) Remove the connector



connected to

the control PCB and 6 screws



(M3-bind

head, round tip), and remove the eject

drive unit



Figure 3-626

18. Eject Drive Roller

1) Remove the eject drive unit.

(Page 3-38)

2) Loosen the screw



(M3-bind head,

round tip) of the tension plate. And remove

the stopper



and the belt



Figure 3-627

3) Open the fitting parts to remove the pul-

ley



and pin



. And remove the

stopper



and bearing



on each side.

And while escaping the lever



, remove

the eject drive roller



Note:

Do not lose the pin.

Figure 3-628

Summary of Contents for imageFORMULA DR-G2140





































































































































































































Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews:

Canon imageFORMULA DR-G2140, Service Manual, Page: 100 / 196

Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews: