Canon imageFORMULA DR-G2140 Service Manual Download Page 87

Page: 87 / 196

3-25

CHAPTER 3 DISASSEMBLY & REASSEMBLY

Figure 3-503



Notes on assembling

The cables connected to the CIS unit

should be formed with extra because the

CIS unit slides to get shading data.

Connect 2 cables to the CIS unit, and then

insert the cable band with lock. And

placed these cables in the groove of

sponge packing and then assemble the

cover.

Pass the motor, grounding and sensor ca-

bles through a hole before assembling the

reading unit. Be careful not to allow these

cables to be caught.

2. Shading Motor

1) Remove the upper reading unit.

(Page 3-24)

2) Remove 2 screws



(M3-bind head,

round tip) and remove the shading mo-

tor



Figure 3-504

Summary of Contents for imageFORMULA DR-G2140





































































































































































































Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews:

Canon imageFORMULA DR-G2140, Service Manual, Page: 87 / 196

Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews: