Canon imageFORMULA DR-G2140 Service Manual Download Page 97

Page: 97 / 196

3-35

CHAPTER 3 DISASSEMBLY & REASSEMBLY

Figure 3-618

4) Remove the E-rings



and bearing

holder



(including bearing) on each side

and remove the platen lower roller



. And

then remove the gear



(including one-

way clutch) and stopper



Figure 3-619

13. Reading Lower Roller

1) Remove the right and left covers.

(Page 3-3)

(Page 3-5)

2) Remove the right belt.

(Page 3-31)

3) Remove the platen unit.

(Page 3-34)

5) For the reading lower roller



, remove the

stopper



, pulley



and pin



on the

right side. And remove the stopper



the left side, and bearing



on each side.

And remove the roller.

Note:

Do not lose the pin.

Figure 3-620

Summary of Contents for imageFORMULA DR-G2140





































































































































































































Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews:

Canon imageFORMULA DR-G2140, Service Manual, Page: 97 / 196

Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews: