Canon imageFORMULA DR-G2140 Service Manual Download Page 147

Page: 147 / 196

5-13

CHAPTER 5 TROUBLESHOOTING

3. Firmware version

This is used to check the versions of the

main body firmware and the internal devices

of the scanner.

Also, it can be checked by the user mode

“Maintenance” using the operation panel ex-
cepting the [SERIAL NUMBER].

Figure 5-214



[MAIN CPU]

Control PCB firmware



[SUB CPU1]

Main drive PCB firmware



[SUB CPU2]

Sub drive PCB firmware



[IMPRINTER CPU]

Imprinter firmware



[USS SNS PCB]

USS sensor PCB firmware



[EXIT CONTROLLER]

Exit PCB firmware



[SERIAL NUMBER]

Special serial number for main body

Note:

The [SERIAL NUMBER] above could

not be changed in the market. If you re-

placed the control PCB to the service

parts, this number does not display.

4. Error History

This is used to check the error code and

occurrence time. Displays up to 8 errors.

Figure 5-215

Refer to the “I. ERROR DISPLAY” to the

contents of error code.

Note that not all errors are displayed. For

example, errors occurred before scanning,

cover open (C001/C009), and document re-

maining (P000), or error could not record,

EEPROM writing error (E086) and others.

And only the first error code is displayed,

such that the error indicated may differ from

the observed error.

Also, while the computer is not connected

or the computer does not control the time, oc-

currence time cannot be displayed.

Summary of Contents for imageFORMULA DR-G2140





































































































































































































Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews:

Canon imageFORMULA DR-G2140, Service Manual, Page: 147 / 196

Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews: