Canon imageFORMULA DR-G2140 Service Manual Download Page 108

Page: 108 / 196

3-46

CHAPTER 3 DISASSEMBLY & REASSEMBLY

10. Separation Motor

1) Remove the registration lower roller.

(Page 3-33)

2) Remove the cooling fan.

(Page 3-48)

3) Remove 3 screws



(M3-bind head,

round tip) and 2 connectors



and pull

out the retard roller drive assembly



Figure 3-718

4) Remove 2 screws



(M3-bind head,

round tip) and remove the separation mo-

tor



Figure 3-719

Note:



indicated in the above figure

shows the motor cable position.

11. Eject Motor

1) Remove the eject drive unit.

(Page 3-38)

2) Loosen the screw



(M3x6, bind head)

and remove the stopper



and remove

the belt



. Then remove the pulley



belt



and coil spring



Figure 3-720

Summary of Contents for imageFORMULA DR-G2140





































































































































































































Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews:

Canon imageFORMULA DR-G2140, Service Manual, Page: 108 / 196

Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews: