manualshive.com logo in svg

Canon imageFORMULA DR-G2140, Service Manual, Page: 118 / 196

Share
Download
Canon imageFORMULA DR-G2140 Service Manual Download Page 118

 

4-2

 

COPYRIGHT © CANON ELECTRONICS INC. 2018           CANON DR-G2140/G2110/G2090 FIRST EDITION

 

CHAPTER 4 INSTALLATION & MAINTENANCE 

2. Unpacking And Installation

 

When metallic objects are brought from a 

cold room into a warm room, small drops of 
water  may  be  formed  on  the  surfaces. This 
phenomenon  is  called  condensation  and  if 
the machine with condensation is used, vari-

ous problems may take place. Therefore, al-
low this machine at least one hour to adjust to 
room  temperature  before  moving  the ma-
chine from a cold room into a warm room and 
installing it. 

.

No. 

Step 

Details/Remarks 

1  Remove the box joints (4) and lift and re-

move the cardboard box. 
The packing weight is approx. 30 kg and 
the  dimensions  are  approx.  600  (W) 

 

680 (D) 

 450(H) mm. 

 

Note:  

1)  Do not open the top of the cardboard 

box, but remove the entire cardboard 
box. 

 

 

 

 

 

  

 

Summary of Contents for imageFORMULA DR-G2140





































































































































































































Reviews:

No comments