Canon imageFORMULA DR-G2140 Service Manual Download Page 161

Page: 161 / 196

5-27

CHAPTER 5 TROUBLESHOOTING

2. Move

This is used to check operation of the mo-

tors.

It is shown the operation screen area and

list of items below.

Figure 5-251

Display

Items

Resolution

300 / 600 (dpi)

Mode

Gray / Color

Direction

*Forward / Revers
*Forward / Revers / Hold
(Separation motor only)
*Forward
(Eject motor only)

Table 5-203

Select operating conditions for a motor,

then select [Start] to run the motor. Select

[Start] again to stop the motor.

3. Position

This is used to check operation of the mo-

tors.

It is shown the operation screen area and

list of items below.

Figure 5-252

Display



Motor name

Items

TrayHP



Tray motor

TrayTop
100 paper
300 paper
500 paper

CIS Position



Shading motor

Shading
Scan

Pick position



pickup up/down
motor

PickOff
PickHP
PickBottom
PickUp

Table 5-204

Select operating position for a motor, then

select [Start] to run the motor. And motor

stops.

Summary of Contents for imageFORMULA DR-G2140





































































































































































































Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews:

Canon imageFORMULA DR-G2140, Service Manual, Page: 161 / 196

Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews: