Canon imageFORMULA DR-G2140 Service Manual Download Page 130

Page: 130 / 196

4-14

CHAPTER 4 INSTALLATION & MAINTENANCE

2. Consumable Goods (Commercial Goods)

The list below shows the consumable goods specified as commercial goods. The user re-

places them.

No.

Item name

Item code

Expected

life

Remarks

Exchange roller
kit

Pickup roller
Feed roller
Retard roller

3601C002

3601C003 for
China only

600,000
sheets

Due to the worn rollers, it is
replaced when the pickup fail-
ures or the document jams oc-
cur after cleaning.

Separation pad
(cover)

3601C005

3601C006 for
China only

6,000,000
sheets

Due to the worn pads, it is re-
placed when the pickup fail-
ures or the document jams oc-
cur after cleaning.

Ink cartridge:
blue

3693A002

1,750,000
characters

For imprinter.
Replace if ink runs out.
The condition of expected life
is 8



12 font, 32 charac-

ters/sheet, 100 sheets/batch,
including preliminary applica-
tion.

Ink cartridge:
red

3693A003

Table 4-202

3. Consumable Parts (Service Parts)

The list below shows the consumable parts that are specified as service parts and can be

replaced by the service technician.

No.

Parts name

Parts number

Expected

life

Remarks

IP pad unit

MG1-4311

6,000,000
sheets

When using an imprinter.
Replace if ink is not absorbed

and the document gets dirty.

Table 4-203

Note:

Each individual part of the exchange roller kit and separation pad (separation cover) in the
“2. Consumable Goods” is assigned as service parts too.

Summary of Contents for imageFORMULA DR-G2140





































































































































































































Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews:

Canon imageFORMULA DR-G2140, Service Manual, Page: 130 / 196

Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews: