Canon imageFORMULA DR-G2140 Service Manual Download Page 145

Page: 145 / 196

5-11

CHAPTER 5 TROUBLESHOOTING

4. Application Information

This mode is used to check the detailed

version of the service mode software (EXE

file).

Select [Help] from the toolbar at the top of

the screen and then select [Application infor-

mation].

Figure 5-209

5. Simulation Mode

This mode is used to train service techni-

cians about service mode without connecting

to the scanner.



Operation Procedure

1) Enter the 8 characters “training” as the

password.

Figure 5-210

2) The screen is the same as in the real pro-

cedure, and can be operated in the same

way except for some buttons that are

grayed out.

Note:

You cannot execute operations that re-

quire communication with the scanner.

Summary of Contents for imageFORMULA DR-G2140





































































































































































































Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews:

Canon imageFORMULA DR-G2140, Service Manual, Page: 145 / 196

Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews: