Canon imageFORMULA DR-G2140 Service Manual Download Page 185

Page: 185 / 196

5-51

CHAPTER 5 TROUBLESHOOTING

5. Streaks on Image

If the reading glass surface is dirty, streaks appear on the scanned images in the feed direc-

tion. Dirt on the rollers may also be transferred to the documents.

On the other hand, white streaks appearing on the scanned images are caused by the exe-

cution of the shading correction while the inside of reading unit is dirty.

Cause/Faulty

Locations

Step

Check Item

Result

Action

Reading glasses

Are the reading glasses
clean?

Clean the reading
glasses.
Replace the reading
glass if scratches are
found.

Roller

Are the surfaces clean?

Clean or replace the
roller.

Feed path

Is the feed path clean?

Clean the feed path.

Reading unit inside

Is the reading unit inside
clean?

Clean or replace the
reading unit.

Table 5-506

6. Outer Areas of Image Disappear

When scanning a document with black or deep color outer areas, selecting the

“Auto-detec-

tion,

” the “Deskew” or the “Border Removal” may cause the outer areas to disappear from the

scanned image.

Cause/Faulty

Locations

Step

Check Item

Result

Action

Document

Is there any black or deep
color on the document
outer areas?

YES

Disable the functions
such as the

“Auto-detec-

tion

”.

Table 5-507

Summary of Contents for imageFORMULA DR-G2140





































































































































































































Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews:

Canon imageFORMULA DR-G2140, Service Manual, Page: 185 / 196

Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews: