Canon imageFORMULA DR-G2140 Service Manual Download Page 148

Page: 148 / 196

5-14

CHAPTER 5 TROUBLESHOOTING

5. Serial Number

This is used to check the serial number.

Figure 5-216

Serial number data is saved on the con-

trol PCB. When the control PCB is replaced,

values are displayed validly by selecting the

[Edit] button on the information screen.

Figure 5-217

Enter the serial number shown on the rat-

ing label on the main body.

Figure 5-218

After entry, select the [Apply] button on

the information screen and save the values.

If the [Cancel] button is selected on the

information screen, the changed values are

not saved.

Figure 5-219

6. Sleep Mode

This is used to check and change the time

before entering sleep mode. This is set to [Af-

ter 10 minutes] by factory default.

Also, it can be checked by the user mode

using the operation panel. If you change this

setting, notify the user that you are changing

it.

Figure 5-220

To change the sleep mode setting, select

the [Edit] button in the information screen to

enable selection and setting change.

Figure 5-221

After selecting, be sure to select the [Ap-

ply] button on the information screen and

save the setting.

If the [Cancel] button is selected on the

information screen, the changed settings are

not saved.

These button operations are the same as

“Serial Number” and others.

Summary of Contents for imageFORMULA DR-G2140





































































































































































































Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews:

Canon imageFORMULA DR-G2140, Service Manual, Page: 148 / 196

Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews: