Canon imageFORMULA DR-G2140 Service Manual Download Page 181

Page: 181 / 196

5-47

CHAPTER 5 TROUBLESHOOTING

5. Scanning Speed is Slow

The speed is further reduced if high resolution, color settings, or special functions are selected.

If the scanning speed is slow after taking these considerations, the cause may be as follows.

Cause/Faulty

Locations

Step

Check Item

Result

Action

Insufficient com-
puter memory

Is the memory sufficient?

Increase the memory.

Are other applications
running?

YES

Close the other applica-
tions.

Are resident applications
such as a virus protection
program running?

YES

Close the service-type ap-
plications.

Is there insufficient hard
disc space?

YES

Increase the hard disc
space.

USB3.1 Gen1 and
USB 2.0 not sup-
ported

Is the USB port of com-
puter supported?

Use a computer that sup-
ports it.

Is the USB cable sup-
ported?

Use the supplied USB ca-
ble.

Is the USB HUB sup-
ported?

Use a USB HUB that sup-
ports it.

The log file setting
is [Full]

Is the log file setting set to
[Full]?

YES

Set to [Standard].

Table 5-406

Summary of Contents for imageFORMULA DR-G2140





































































































































































































Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews:

Canon imageFORMULA DR-G2140, Service Manual, Page: 181 / 196

Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews: