Canon imageFORMULA DR-G2140 Service Manual Download Page 140

Page: 140 / 196

5-6

CHAPTER 5 TROUBLESHOOTING

A list of items is shown below.

No.

Component/display name

Function

Information

Scanner name

Display the scanner name.

Background color

Display the background color.

Firmware version

Display the current firmware version.

Error history

Display the latest error code up to 8.

Serial number

Display the serial number of the main body.

Sleep mode

Display the sleep mode selected.

Auto power off

Display the auto power off selected.

Counter

Display the counter for each item.

Write file

Save the above information on the text file.

Edit

Change the value and setting for the serial number,
sleep mode, auto power off and counter.

Cancel

Cancel the changed value and setting.

Apply

Save the changed value and setting.

14 Adjustment

All

Execute the automatic adjustment for the scaling
and registration (reading position).

Scaling (Manual)

Display the manual adjustment value of the scaling.

Registration (Manual)

Display the manual adjustment value of the regis-
tration.

Density (Auto)

Execute the automatic adjustment for the density.

Density (Manual)

Display the manual adjustment value for the den-
sity.

Edit

Change the value for the manual adjustment.

Cancel

Cancel the changed value.

Apply

Save the changed value.

23 Motor / Sensor

CIS

Check the LED in the reading unit.

LCD

Check the LCD in the operation panel.

Buzzer

Check the buzzer on the control PCB.

Move

Check the motor operation.

Position

Check the position of tray, CIS, pickup roller.

Cover Open

Check the sensor operation.

Panel

Check the key in the display panel.

Table 5-201a

Summary of Contents for imageFORMULA DR-G2140





































































































































































































Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews:

Canon imageFORMULA DR-G2140, Service Manual, Page: 140 / 196

Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews: