Canon imageFORMULA DR-G2140 Service Manual Download Page 68

Page: 68 / 196

3-6

CHAPTER 3 DISASSEMBLY & REASSEMBLY

5. Top Cover

1) Remove the control PCB cover.

(Page 3-3)

2) Remove the right and left covers.

(Page 3-3), (Page 3-5)

3) Remove the screw



(M3-TP head,

round tip). Then hang on your fingers un-

der the cover at front/center



, and move

to front/upper side to remove a fitting part

inside. After that, while unhooking 2 pairs
of the right and left fitting parts



, re-

move the top cover



Note:

Don’t deform the static eliminator
brush when you hang on your fingers

under the cover.

Figure 3-210

Figure 3-211



Notes on assembling

After assembling, push the cover to check

the fitting part on front side is without any

floating.

Figure 3-212

Summary of Contents for imageFORMULA DR-G2140





































































































































































































Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews:

Canon imageFORMULA DR-G2140, Service Manual, Page: 68 / 196

Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews: