Canon imageFORMULA DR-G2140 Service Manual Download Page 122

Page: 122 / 196

4-6

CHAPTER 4 INSTALLATION & MAINTENANCE

No.

Step

Details/Remarks

6 Install software in the computer used for

operation check as required.

Note:

From Step No.6, refer to the User

Manual or Setup Guide for details.



If it has already been installed in the
computer for servicing, it does not
need to be installed during installation.



If the service technician installs it in
the user's computer, obtain the user’s
approval beforehand.



If the user installs it, ask the user to
install it according to the “Setup
Guide”.

Note:

1) Ensure that the specification of com-

puter and type of the operating system
are correct.

2) Do not connect the scanner to the

computer before installing software.

3) Be sure to log on with administrator

privileges.

1) Insert the Setup Disc into the disc drive.

2) The setup menu starts.

Click [Typical Installation] or [Custom In-
stallation].

3) Later on, perform operation according to the

screen instructions.

4) When all installation is completed, the in-

stallation completion screen is displayed.
Click [Exit].

Summary of Contents for imageFORMULA DR-G2140





































































































































































































Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews:

Canon imageFORMULA DR-G2140, Service Manual, Page: 122 / 196

Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews: