Canon imageFORMULA DR-G2140 Service Manual Download Page 38

Page: 38 / 196

2-12

CHAPTER 2 FUNCTION & OPERATION

3. Shading

The CIS unit and its slide mechanism are

assembled inside the reading unit.

The CIS unit is positioned in the docu-

ment reading position when the documents

are read. Since the scanner needs to read the

white reference on a surface of the reading

glass when determining the shading correc-

tion value, it slides the CIS unit. The guide

plate is assembled for protection of the white

reference.

The position of the CIS unit when reading

an image and white reference is shown below.

This slide plate is driven by the shading

motor. Since the white reference is attached

on a surface of the reading glass, the reflec-

tion distances during image reading and white

reference reading can be made equal.

When the power is turned ON and when

scanning starts, this machine slides the CIS

unit and reads the white reference data to de-

cide the shading correction value.

Document side CIS unit side

Figure 2-203

Figure 2-204

Guide plate

White reference

Reading glass

Summary of Contents for imageFORMULA DR-G2140





































































































































































































Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews:

Canon imageFORMULA DR-G2140, Service Manual, Page: 38 / 196

Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews: