Canon imageFORMULA DR-G2140 Service Manual Download Page 112

Page: 112 / 196

3-50

CHAPTER 3 DISASSEMBLY & REASSEMBLY

Figure 3-803



Notes on assembling

The cables connected to the CIS unit

should be formed with extra because the

CIS unit slides to get shading data.

Connect 2 cables to the CIS unit, and then

insert the cable band with lock. And placed

these cables in the groove of sponge pack-

ing and then assemble the cover.

Pass the motor, grounding and sensor ca-

bles through a hole before assembling the

reading unit. Be careful not to allow these

cables to be caught.

2. Shading Motor

1) Remove the lower reading unit.

(Page 3-49)

2) Remove 2 screws



(M3-bind head,

round tip) and remove the shading mo-

tor



Figure 3-804

Summary of Contents for imageFORMULA DR-G2140





































































































































































































Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews:

Canon imageFORMULA DR-G2140, Service Manual, Page: 112 / 196

Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews: