Canon imageFORMULA DR-G2140 Service Manual Download Page 135

Page: 135 / 196

5-1

CHAPTER 5 TROUBLESHOOTING

I. ERROR DISPLAY

1. Main Body

When an error is occurred,

“Message”

and “Code” appear on the display panel of the
main body.

The service call message is displayed the

message as

“Scanner hardware problem”

and code as “Exxx”.



Display example

Figure 5-101



Errors associated with user operations

No.

Message

Code

Failure

Scanner cover is open.

C001

The upper unit is open.

C009

The imprinter cover is open.

A double paper-feed has
occurred.

D002

A double feed was detected by the document length.

D004

A double feed was detected ultrasonically.

Imprinter Insert Error

H001

An imprinter voltage error was detected...

H004

An ink cartridge is not installed in the imprinter.

Staple was Detected.

J001

A stapled document has been detected.

A document was skewed.

J018

A skewed document was detected.

Dust was detected

J050

Dust was detected on the reading glass.

Paper jammed in scanner.

P000

A document has detected in a feed path before scanning.

P001

A document has jammed before entering the registration
pre-sensor.

P002

A document has jammed before exiting from the registra-
tion pre-sensor.

P004

A document has jammed at the eject sensor.

P006

A document has jammed before entering the registration
post-sensor.

P007

A document has jammed before exiting from the registra-
tion post-sensor.

P010

A document has jammed before entering the eject sensor.

P050

Feeding stopped due to other document jams.

The count does not match.

U001

The specified number of sheets was exceeded before the
scan ended.

U002

The scan ended with a number of sheets less than the set-
ting.

Table 5-101

Summary of Contents for imageFORMULA DR-G2140





































































































































































































Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews:

Canon imageFORMULA DR-G2140, Service Manual, Page: 135 / 196

Search results

Summary of Contents for imageFORMULA DR-G2140

Reviews: