manualshive.com logo in svg

Canon imageFORMULA DR-G2140, Service Manual, Page: 81 / 196

Share
Download
Canon imageFORMULA DR-G2140 Service Manual Download Page 81

 

COPYRIGHT © CANON ELECTRONICS INC. 2018                      CANON DR-G2140/G2110/G2090 FIRST EDITION

 

3-19

 

CHAPTER 3 DISASSEMBLY & REASSEMBLY 

13. Entire Upper Unit 

Note: 

You need to prepare space for placing 

the upper unit before remove it. 

1) Remove the control PCB cover. 

 

(Page 3-3)

 

2) Remove the right and left covers. 

 

(Page 3-3)

, 

(Page 3-5)

 

3)  Remove the eject tray unit. 

 

(Page 3-7)

 

4)  Remove  3  cables

1

  and  locked  cable 

band on the control PCB. And open the ca-

ble holders to release the cables and pull 

them in to the upper unit. 

Figure 3-328 

 

5)  To prevent damage to the feed surface, put 

paper or a sheet

1

  on the feed surface of 

the base section, and close the upper unit. 

Note: 

If  the  dampers  are  removed  using  the 

following procedure, the upper unit can-

not be kept open, so be sure to close it. 

 

Figure 3-329 

 

6)  Removing  6  screws

1

  (3  on  both  sides, 

M4-TP  head,  round  tip)  to  remove  the 

hinge

2

,  and  remove  4  screws

3

  (2  on 

both sides,  M3-TP head, round tip) to re-

move  the  damper

4

  (black)  and 

damper

5

  (white). Then remove right side 

screw

6

  (M3-bind head, round tip) to  re-

move the stopper plate

7

, and remove left 

side  screw

6

  to  remove  the  grounding 

plate

8

.   

Note:

 The right and left hinges are the same 

parts  but  the  dampers  are  different 

parts.   

Summary of Contents for imageFORMULA DR-G2140





































































































































































































Reviews:

No comments