Avaya IP Ofice 8.0 Quick Mode Instaltion Download Page 77

Page: 77 / 256

IP Office Basic Edition - Quick Mode Installation

Page 77

15-601042 Issue 24i (20 December 2011)

IP Office 8.0

IP500 V2 Installation: Starting the System

4.10.1 Checking the LEDs

Control Unit LEDs

LED

Description

Optional SD

Off =

Card shutdown

Green on = Card present.

Green flashing = Card in use.

Orange steady = Reset imminent.

Red flashing = Card initializing or shutting down.

Red fast flashing = card full

Red steady = Card failure/wrong type.

System SD

CPU

Alternate red/green = Starting up.

Green on = Okay.

Red on = No software.

Flashing Red = Error/Shutdown.

Base Card LEDs

Base Card

LEDs 1 to 8 Usage

All Cards

LED1 is also used for base card status:

Red On = Error

Red Slow Flash = Initializing.

Red Flash every 5 seconds = Card okay.

Red Fast Flash = System shutdown.

IP500 Analog Phone

No status LEDs are used for analog phone extensions.

IP500 Digital Station

Green On = Phone detected.

IP500 Combination

LEDs 1 to 6

Green On = Phone detected.

Trunk Daughter Card LEDs

Trunk Daughter Card

LEDs 9 to 12 Usage

All cards

LED 9 is also used for daughter card status.

Red On = Error

Red Slow Flash = Initializing.

Red Flash every 5 seconds = Card okay.

Red Fast Flash = System shutdown.

Analog Trunk

Green on = Card fitted.

Green flashing = Trunk in use.

PRI Trunk

Off = No trunk present.

Green on = Trunk present.

Green flashing = Trunk in use.

Red/Green Fast Flash (port 9) or Green Fast Flash (port 10) = Alarm indication
signal (AIS) from the trunk remote end.

Red with Green Blink (port 9) or Green Blink (port 10) = Port in loopback mode (set
through IP Office System Monitor).

BRI Trunk

Off = No trunk present.

Green on = Trunk present.

Green flashing = Trunk in use.

External Expansion Module LEDs

Green on = Module okay.

Red flashing = Module starting up/Loading firmware.

Green flashing = Module starting up/Loading firmware (IP500 DS16A/30A module).

Red on = Error.

150

Summary of Contents for IP Ofice 8.0

































































































































































































































































Search results

Summary of Contents for IP Ofice 8.0

Reviews:

Related manuals for IP Ofice 8.0

Brands by name

Popular brands

Avaya IP Ofice 8.0, Quick Mode Instaltion

Search results

Summary of Contents for IP Ofice 8.0

Reviews:

Related manuals for IP Ofice 8.0

Brands by name

Popular brands