Avaya IP Ofice 8.0 Quick Mode Instaltion Download

Page: 13 / 256

IP Office Basic Edition - Quick Mode Installation

Page 13

15-601042 Issue 24i (20 December 2011)

IP Office 8.0

System Overview: IP Office Modes

1.1.2 Hardware Support Summary

Note that even where indicated as supported, the availability and support of equipment may still be subject to local
restrictions.

IP Office

Basic Edition

- PARTNER®

Mode

IP Office

Basic Edition

- Norstar

Mode

IP Office

Basic Edition

- Quick Mode

IP Office

Essential

Edition

Control Unit

IP500 V2 Control Unit

IP500 Control Unit

–

IP500 Base
Cards

IP500 Digital Station Card

IP500 Analog Phone 2/8 Cards

IP500 TCM8 Card

[1]

IP500 VCM 32/64 Base Cards

–

IP500 Legacy Card Carrier

–

IP500 4-Port Expansion Card

–

IP500 BRI Combination Card

[1]

–

IP500 ATM Combination Card

[1]

IP500 ETR6 Card

[1]

–

C110 Unified Communications
Module

–

IP500 Trunk
Daughter Cards

Analog Trunk Card

BRI Trunk Cards

[5]

–

PRI Trunk Card

[6]

External
Expansion
Modules

Number of Modules

[3]

Digital Station 16/30

Digital Station 16A/30A

Phone 8/16/30

Analog Trunk 16

BRI So8

–

Telephone
Types

ETR Phones (ETR ports)

–

BST Phones (TCM ports)

DS Phones (DS ports)

H323 IP Phones (LAN)

–

SIP IP Phones (LAN)

–

DECT R4 (LAN)

DECT DMS (TCM ports)

Voicemail

Embedded Voicemail

Voicemail Pro

–

1. Not supported by IP500 control units. Support by IP500 V2 systems in IP Office Basic Edition - PARTNER® Mode or

IP Office Basic Edition - Quick Mode U-Law modes only.

2. Only 2 combinations cards are supported in a control unit, regardless of type.

3. External expansion modules can be added so long as the overall limit for extensions and trunks is not exceeded. On

non-IP Office Essential Edition systems, a maximum of one Analog Trunk 16 module is supported.

4. A mix of BRI and PRI trunks is not supported by IP Office Basic Edition - Norstar Mode and IP Office Basic Edition -

Quick Mode.

5. IP Office Basic Edition - PARTNER® Mode, IP Office Basic Edition - Norstar Mode and IP Office Basic Edition - Quick

Mode only support a single-port PRI card.

Summary of Contents for IP Ofice 8.0

































































































































































































































































Search results

Summary of Contents for IP Ofice 8.0

Reviews:

Related manuals for IP Ofice 8.0

Brands by name

Popular brands

Avaya IP Ofice 8.0, Quick Mode Instaltion

Search results

Summary of Contents for IP Ofice 8.0

Reviews:

Related manuals for IP Ofice 8.0

Brands by name

Popular brands