Avaya IP Ofice 8.0 Quick Mode Instaltion Download | Manualshive

Page: 236 / 256

background image

IP Office Basic Edition - Quick Mode Installation

Page 236

15-601042 Issue 24i (20 December 2011)

IP Office 8.0

9.12.3 Trunk Licensing

The following trunks licenses can be used by a IP Office Basic Edition - Quick Mode system.

·

IP500 Universal PRI (Additional channels)

These licenses are used to enable additional B-channels above the basic 8 on an IP500 PRI-U card. The IP500 PRI-U
card supports E1, T1 and E1-R2 PRI modes. The IP Office system supports 8 unlicensed B-channels on each IP500
PRI-U port fitted. Additional B-channels, up to the capacity of ports installed and PRI mode selected require
licenses. These additional channels consume the licenses based on which additional channels are configured as in-
service from port 9 of slot 1 upwards. D-channels are not affected by licensing.

·

IP500 T1 CHANNELS ADD 2CH - 215180.

·

IP500 T1 CHANNELS ADD 8CH - 215181.

·

IP500 T1 CHANNELS ADD 32CH - 215182.

·

IP500 E1 CHANNELS ADD 2CH - 215183.

·

IP500 E1 CHANNELS ADD 8CH - 215184.

·

IP500 E1 CHANNELS ADD 22CH - 215185.

·

IP500 E1R2 CHANNELS ADD 2CH - 215186.

·

IP500 E1R2 CHANNELS ADD 8CH - 215187.

·

IP500 E1R2 CHANNELS ADD 22CH - 215188.

·

SIP Trunk Channels

These licenses are used to configure the maximum number of simultaneous SIP trunk calls supported. A IP Office
Basic Edition - Quick Mode mode system supports 3 channels without licenses.

·

IPO LIC SIP TRNK RFA 1 - 202967.

·

IPO LIC SIP TRNK RFA 5 - 202968.

·

IPO LIC SIP TRNK RFA 10 - 202969.

·

IPO LIC SIP TRNK RFA 20 - 202970.

«
...
234
235
236
237
238
...
»

Summary of Contents for IP Ofice 8.0

































































































































































































































































Reviews:

No comments

Related manuals for IP Ofice 8.0

Brand: Uniden Pages: 16

Brand: Haier Pages: 57

Brand: Samsung Pages: 108

Brand: Aastra Pages: 27

Brand: NEC Pages: 61

Brand: T-Mobile Pages: 211

Brand: Pantech Pages: 51

Brand: Netway Pages: 68

Nortel IP UC Series

Brand: E-MetroTel Pages: 36

Brand: Trium Pages: 74

Brand: Grandstream Networks Pages: 2

Brand: RugGear Pages: 31

Brand: Iget Pages: 43

Brand: Talk To Me Technologies Pages: 2

Brand: Samsung Pages: 175

Brand: Brother Pages: 40

Brand: SoftBank Pages: 24

Brand: Zte Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands